Initial Commit

Fimeware Pre-Rooted, Builds & Flashes

overlay_rootfs/usr/share/klipper/config/F005/printer.cfg

@@ -0,0 +1,256 @@
+# Ender-3V3KE
+# Printer_size: 220x220x240
+# Version: v1.1.0.33
+# CreateDate: 2024/3/27
+# mcu: chip: GD32F303RET6
+#      version: CR4NS200323C10
+[include sensorless.cfg]
+[include gcode_macro.cfg]
+[include printer_params.cfg]
+[mcu]
+serial:/dev/ttyS1
+baud:230400
+restart_method: command
+
+[force_move]
+enable_force_move: True
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[bl24c16f]
+i2c_mcu: rpi
+i2c_bus: i2c.2
+i2c_speed: 400000
+
+######################################################
+[prtouch_v2]
+pres_cnt: 1                     #探点次数
+pres0_clk_pins: PA4             #压力检测时钟引脚配置
+pres0_sdo_pins: PC6             #压力检测数据引脚配置
+step_swap_pin: PA15                 
+pres_swap_pin: PA15
+step_base:2
+# show_msg: True
+tri_min_hold: 1000      
+tri_max_hold: 1500            #压力检测信息展示
+speed: 1
+# tri_wave_ip: 172.22.30.204
+#####################################################
+
+
+[z_compensate]
+tri_min_hold: 1400      
+tri_max_hold: 2000            #压力检测信息展示
+tri_expand_mm = 0.10
+# tri_min_hold: 3
+speed: 5
+hot_start_temp: 180#擦喷嘴是最小温度
+hot_rub_temp: 200#擦喷嘴是最小温度
+hot_end_temp: 140#擦喷嘴是最小温度
+bed_add_temp: 60#调平时的热床温度
+clr_noz_start_x: -3 #擦喷头区域的起始x坐标（默认在热床后方正中心位置）
+clr_noz_start_y: 20 #擦喷头区域的起始y坐标
+clr_noz_len_x: 3 #擦喷头区域的x方向的长度
+clr_noz_len_y: 50 #擦喷头区域的y方向的长度
+pa_clr_dis_mm_x = 0
+pa_clr_dis_mm_y =30
+# show_msg = True
+bl_offset: 0,27
+noz_pos_center: 20,25
+noz_pos_offset: 3,7
+pumpback_mm: 10
+vs_start_z_pos: 3
+pr_probe_cnt: 3
+pr_clear_probe_cnt: 3
+type_nozz = 0
+
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 8000
+max_accel_to_decel: 2500
+max_z_velocity: 30
+square_corner_velocity: 5.0
+max_z_accel: 300
+
+[idle_timeout]
+timeout: 99999999
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA5
+position_endstop: -12
+position_min: -12
+position_max: 221
+homing_speed: 30
+homing_retract_dist:0 #10
+
+[tmc2208 stepper_x]
+uart_pin:PB12
+interpolate: True
+run_current:0.75
+sense_resistor: 0.150
+stealthchop_threshold: 0
+
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 60
+endstop_pin: !PA6
+position_endstop: -20
+position_min: -20
+position_max: 223
+homing_speed: 30
+homing_retract_dist:0
+
+[tmc2208 stepper_y]
+uart_pin:PB13
+interpolate: True
+run_current:0.75
+sense_resistor: 0.150
+stealthchop_threshold: 0
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance:8
+endstop_pin:probe:z_virtual_endstop#PA15   #probe:z_virtual_endstop
+position_max: 246
+position_min: -5
+
+[tmc2208 stepper_z]
+uart_pin: PB14
+interpolate: True
+run_current: 0.8
+stealthchop_threshold: 0
+sense_resistor: 0.150
+
+
+[bltouch]
+sensor_pin:PC14
+control_pin: PC13
+x_offset: 0
+y_offset: 27
+z_offset: 0
+probe_with_touch_mode: true
+stow_on_each_sample: false
+speed:5
+lift_speed:20
+
+
+[filament_switch_sensor filament_sensor]
+switch_pin: !PC15
+pause_on_runout: true
+
+[output_pin MainBoardFan]
+pin: !PB1
+
+[extruder]
+max_extrude_only_distance:1000
+max_extrude_cross_section:80
+pressure_advance = 0.036
+step_pin: PB4
+dir_pin: PB3
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 7.53
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control = pid
+pid_Kp=20.584 
+pid_Ki=1.737 
+pid_Kd=60.981
+min_temp: 0
+max_temp: 320 # Set to 300 for S1 Pro
+
+
+[heater_bed]
+heater_pin: PB2
+sensor_type: EPCOS 100K B57560G104F 
+sensor_pin: PC4
+control = pid
+pid_kp = 70.652
+pid_ki = 1.798
+pid_kd = 694.157
+min_temp: 0
+max_temp: 120 # 
+temp_offset_flag = True
+
+[verify_heater extruder]
+[verify_heater heater_bed]
+check_gain_time: 120
+heating_gain: 1.0
+hysteresis: 10
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[output_pin fan0]
+pin:PA0
+pwm: True
+cycle_time: 0.0100
+hardware_pwm: false
+value: 0.00
+scale: 255
+shutdown_value: 0.0
+
+[heater_fan nozzle_fan]
+pin: PC1
+max_power: 1.0
+shutdown_speed: 0
+cycle_time: 0.010
+hardware_pwm: False
+kick_start_time: 0.100
+off_below: 0.0
+heater: extruder
+fan_speed: 1.0
+heater_temp: 60.0
+
+
+[bed_mesh]
+speed: 350
+mesh_min: 5,10        #need to handle head distance with bl_touch
+mesh_max: 215,215       #max probe range
+probe_count: 5,5
+fade_start: 1
+fade_end: 10
+fade_target: 0
+horizontal_move_z: 8
+
+[input_shaper]
+shaper_type_y = mzv
+shaper_freq_y = 32.0
+
+shaper_type_x = mzv
+shaper_freq_x = 38.5
+
+[mcu rpi]
+serial: /tmp/klipper_host_mcu
+
+[adxl345]
+cs_pin: rpi:None
+spi_speed: 2000000
+spi_bus: spidev2.0
+axes_map: z,y,x
+
+[resonance_tester]
+accel_chip: adxl345
+accel_per_hz: 70
+probe_points: 117.5,117.5,100
+max_freq: 90