mirror of
https://github.com/Dark98/Ender-3_V3_KE_Klipper.git
synced 2026-07-02 16:49:04 +00:00
liyongjie
257 lines
4.9 KiB
INI
Executable File
257 lines
4.9 KiB
INI
Executable File
# Ender-3V3KE
|
|
# Printer_size: 220x220x240
|
|
# Version: v1.2.8
|
|
# CreateDate: 2023/11/06
|
|
# mcu: chip: GD32F303RET6
|
|
# version: CR4NS200323C10
|
|
[include sensorless.cfg]
|
|
[include gcode_macro.cfg]
|
|
[include printer_params.cfg]
|
|
[mcu]
|
|
serial:/dev/ttyS1
|
|
baud:230400
|
|
restart_method: command
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[bl24c16f]
|
|
i2c_mcu: rpi
|
|
i2c_bus: i2c.2
|
|
i2c_speed: 400000
|
|
|
|
######################################################
|
|
[prtouch_v2]
|
|
pres_cnt: 1 #探点次数
|
|
pres0_clk_pins: PA4 #压力检测时钟引脚配置
|
|
pres0_sdo_pins: PC6 #压力检测数据引脚配置
|
|
step_swap_pin: PA15
|
|
pres_swap_pin: PA15
|
|
step_base:2
|
|
# show_msg: True
|
|
tri_min_hold: 1000
|
|
tri_max_hold: 1500 #压力检测信息展示
|
|
speed: 1
|
|
# tri_wave_ip: 172.22.30.204
|
|
#####################################################
|
|
|
|
|
|
[z_compensate]
|
|
tri_min_hold: 1400
|
|
tri_max_hold: 2000 #压力检测信息展示
|
|
tri_expand_mm = 0.10
|
|
# tri_min_hold: 3
|
|
speed: 5
|
|
hot_start_temp: 180#擦喷嘴是最小温度
|
|
hot_rub_temp: 200#擦喷嘴是最小温度
|
|
hot_end_temp: 140#擦喷嘴是最小温度
|
|
bed_add_temp: 60#调平时的热床温度
|
|
clr_noz_start_x: -3 #擦喷头区域的起始x坐标（默认在热床后方正中心位置）
|
|
clr_noz_start_y: 20 #擦喷头区域的起始y坐标
|
|
clr_noz_len_x: 3 #擦喷头区域的x方向的长度
|
|
clr_noz_len_y: 50 #擦喷头区域的y方向的长度
|
|
pa_clr_dis_mm_x = 0
|
|
pa_clr_dis_mm_y =30
|
|
# show_msg = True
|
|
bl_offset: 0,27
|
|
noz_pos_center: 20,25
|
|
noz_pos_offset: 3,7
|
|
pumpback_mm: 10
|
|
vs_start_z_pos: 3
|
|
pr_probe_cnt: 3
|
|
pr_clear_probe_cnt: 3
|
|
type_nozz = 0
|
|
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 500
|
|
max_accel: 8000
|
|
max_accel_to_decel: 2500
|
|
max_z_velocity: 30
|
|
square_corner_velocity: 5.0
|
|
max_z_accel: 300
|
|
|
|
[idle_timeout]
|
|
timeout: 99999999
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !PA5
|
|
position_endstop: -12
|
|
position_min: -12
|
|
position_max: 221
|
|
homing_speed: 30
|
|
homing_retract_dist:0 #10
|
|
|
|
[tmc2208 stepper_x]
|
|
uart_pin:PB12
|
|
interpolate: True
|
|
run_current:0.75
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 60
|
|
endstop_pin: !PA6
|
|
position_endstop: -20
|
|
position_min: -20
|
|
position_max: 223
|
|
homing_speed: 30
|
|
homing_retract_dist:0
|
|
|
|
[tmc2208 stepper_y]
|
|
uart_pin:PB13
|
|
interpolate: True
|
|
run_current:0.75
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance:8
|
|
endstop_pin:probe:z_virtual_endstop#PA15 #probe:z_virtual_endstop
|
|
position_max: 246
|
|
position_min: -5
|
|
|
|
[tmc2208 stepper_z]
|
|
uart_pin: PB14
|
|
interpolate: True
|
|
run_current: 0.8
|
|
stealthchop_threshold: 0
|
|
sense_resistor: 0.150
|
|
|
|
|
|
[bltouch]
|
|
sensor_pin:PC14
|
|
control_pin: PC13
|
|
x_offset: 0
|
|
y_offset: 27
|
|
z_offset: 0
|
|
probe_with_touch_mode: true
|
|
stow_on_each_sample: false
|
|
speed:5
|
|
lift_speed:20
|
|
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: !PC15
|
|
pause_on_runout: true
|
|
|
|
[output_pin MainBoardFan]
|
|
pin: !PB1
|
|
|
|
[extruder]
|
|
max_extrude_only_distance:1000
|
|
max_extrude_cross_section:80
|
|
pressure_advance = 0.036
|
|
step_pin: PB4
|
|
dir_pin: PB3
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 7.53
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
control = pid
|
|
pid_Kp=20.584
|
|
pid_Ki=1.737
|
|
pid_Kd=60.981
|
|
min_temp: 0
|
|
max_temp: 320 # Set to 300 for S1 Pro
|
|
|
|
|
|
[heater_bed]
|
|
heater_pin: PB2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
control = pid
|
|
pid_kp = 70.652
|
|
pid_ki = 1.798
|
|
pid_kd = 694.157
|
|
min_temp: 0
|
|
max_temp: 120 #
|
|
temp_offset_flag = True
|
|
|
|
[verify_heater extruder]
|
|
[verify_heater heater_bed]
|
|
check_gain_time: 120
|
|
heating_gain: 1.0
|
|
hysteresis: 10
|
|
|
|
[temperature_sensor mcu_temp]
|
|
sensor_type: temperature_mcu
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[output_pin fan0]
|
|
pin:PA0
|
|
pwm: True
|
|
cycle_time: 0.0100
|
|
hardware_pwm: false
|
|
value: 0.00
|
|
scale: 255
|
|
shutdown_value: 0.0
|
|
|
|
[heater_fan nozzle_fan]
|
|
pin: PC1
|
|
max_power: 1.0
|
|
shutdown_speed: 0
|
|
cycle_time: 0.010
|
|
hardware_pwm: False
|
|
kick_start_time: 0.100
|
|
off_below: 0.0
|
|
heater: extruder
|
|
fan_speed: 1.0
|
|
heater_temp: 60.0
|
|
|
|
|
|
[bed_mesh]
|
|
speed: 350
|
|
mesh_min: 5,10 #need to handle head distance with bl_touch
|
|
mesh_max: 215,215 #max probe range
|
|
probe_count: 5,5
|
|
fade_start: 1
|
|
fade_end: 10
|
|
fade_target: 0
|
|
horizontal_move_z: 8
|
|
|
|
[input_shaper]
|
|
shaper_type_y = mzv
|
|
shaper_freq_y = 32.0
|
|
|
|
shaper_type_x = mzv
|
|
shaper_freq_x = 38.5
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[adxl345]
|
|
cs_pin: rpi:None
|
|
spi_speed: 2000000
|
|
spi_bus: spidev2.0
|
|
axes_map: z,y,x
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
accel_per_hz: 70
|
|
probe_points: 117.5,117.5,100
|
|
max_freq: 90
|