{
	"type": "filament",
	"name": "Creality Hyper PLA @Ender-5Max-all",
	"inherits": "fdm_filament_common",
	"from": "system",
	"setting_id": "GFSA04_CREALITY_00",
	"filament_id": "01001",
	"instantiation": "true",
	"activate_air_filtration": "0",
	"activate_chamber_temp_control": "0",
	"additional_cooling_fan_speed": "0",
	"chamber_temperature": "0",
	"close_fan_the_first_x_layers": "1",
	"compatible_printers": [
		"Creality Ender-5 Max 0.4 nozzle"
	],
	"complete_print_exhaust_fan_speed": "80",
	"cool_plate_temp": "45",
	"cool_plate_temp_initial_layer": "45",
	"cool_special_cds_fan_speed": "0",
	"default_filament_colour": "\"\"",
	"during_print_exhaust_fan_speed": "60",
	"enable_overhang_bridge_fan": "1",
	"enable_pressure_advance": "1",
	"eng_plate_temp": "50",
	"eng_plate_temp_initial_layer": "50",
	"fan_cooling_layer_time": "100",
	"fan_max_speed": "100",
	"fan_min_speed": "100",
	"filament_cooling_final_speed": "3.4",
	"filament_cooling_initial_speed": "2.2",
	"filament_cooling_moves": "4",
	"filament_cost": [
		"30"
	],
	"filament_density": [
		"1.24"
	],
	"filament_deretraction_speed": "nil",
	"filament_diameter": "1.75",
	"filament_end_gcode": [
		"; filament end gcode \n"
	],
	"filament_flow_ratio": "0.97",
	"filament_is_support": "0",
	"filament_load_time": "0",
	"filament_loading_speed": "28",
	"filament_loading_speed_start": "3",
	"filament_max_volumetric_speed": [
		"50"
	],
	"filament_minimal_purge_on_wipe_tower": "15",
	"filament_multitool_ramming": "0",
	"filament_multitool_ramming_flow": "10",
	"filament_multitool_ramming_volume": "10",
	"filament_notes": "\"\"",
	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
	"filament_retract_before_wipe": "nil",
	"filament_retract_lift_above": "0",
	"filament_retract_lift_below": "0",
	"filament_retract_lift_enforce": "All Surfaces",
	"filament_retract_restart_extra": "nil",
	"filament_retract_when_changing_layer": "nil",
	"filament_retraction_length": "nil",
	"filament_retraction_minimum_travel": "nil",
	"filament_retraction_speed": "nil",
	"filament_shrink": "100%",
	"filament_shrinkage_compensation_z": "100%",
	"filament_soluble": "0",
	"filament_start_gcode": [
		"; filament start gcode\n"
	],
	"filament_toolchange_delay": "0",
	"filament_type": [
		"PLA"
	],
	"filament_unload_time": "0",
	"filament_unloading_speed": "90",
	"filament_unloading_speed_start": "100",
	"filament_vendor": [
		"Creality"
	],
	"filament_wipe": "nil",
	"filament_wipe_distance": "nil",
	"filament_z_hop": "nil",
	"filament_z_hop_types": "nil",
	"full_fan_speed_layer": "0",
	"hot_plate_temp": "45",
	"hot_plate_temp_initial_layer": "45",
	"nozzle_temperature": "220",
	"nozzle_temperature_initial_layer": "220",
	"nozzle_temperature_range_high": "240",
	"nozzle_temperature_range_low": "190",
	"overhang_fan_speed": "100",
	"overhang_fan_threshold": "50%",
	"pressure_advance": "0.04",
	"reduce_fan_stop_start_freq": "1",
	"required_nozzle_HRC": "0",
	"slow_down_for_layer_cooling": "1",
	"slow_down_layer_time": "5",
	"slow_down_min_speed": "20",
	"support_material_interface_fan_speed": "-1",
	"temperature_vitrification": [
		"60"
	],
	"textured_plate_temp": "45",
	"textured_plate_temp_initial_layer": "45"
}
