Initial Profile Sources

profile_sources/non-prusa-fff/Artillery/printer/_common_.ini

@@ -0,0 +1,60 @@
+[printer:*common*]
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0
+between_objects_gcode = 
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = Generic PLA @Artillery
+default_print_profile = 0.20mm NORMAL @Artillery
+deretract_speed = 0
+extruder_colour = #FFFF00
+extruder_offset = 0x0
+gcode_flavor = marlin
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 5000,5000
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 1.5,1.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
+machine_max_jerk_z = 0.4,0.4
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0.25
+max_print_height = 250
+min_layer_height = 0.07
+nozzle_diameter = 0.4
+pause_print_gcode = 
+printer_technology = FFF
+remaining_times = 0
+retract_before_travel = 1
+retract_before_wipe = 0%
+retract_layer_change = 1
+retract_length = 0.8
+retract_length_toolchange = 4
+retract_lift = 0.6
+retract_lift_above = 0
+retract_lift_below = 380
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 35
+silent_mode = 0
+single_extruder_multi_material = 0
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0
+extruder_clearance_height = 25
+extruder_clearance_radius = 45
+end_gcode = G4 ; wait\nG92 E0 ; prepare to retract\nG1 E-0.5 F3000; retract to avoid stringing\n\n; Anti-stringing end wiggle\nG91 ; use relative coordinates\nG1 X1 Y1 F1200\n\n; Raise nozzle and present bed\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+120, max_print_height)}{endif} ; Move print head up\nG90 ; use absolute coordinates\n\n; Reset print setting overrides\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Shut down printer\nM106 S0 ; turn-off fan\nM104 S0 ; turn-off hotend\nM140 S0 ; turn-off bed\nM150 P0 ; turn off led\nM85 S0 ; deactivate idle timeout\nM84 ; disable motors\n
+