Initial Profile Sources

profile_sources/non-prusa-fff/CocoaPress/filament/Cocoa Press Chocolates.ini

@@ -0,0 +1,9 @@
+[filament:Cocoa Press Chocolates]
+inherits = *common*
+temperature = 0
+filament_vendor = Cocoa Press
+filament_settings_id = "Cocoa Press Chocolate"
+filament_type = CHOCOLATE
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_COCOA_PRESS.*/
+

profile_sources/non-prusa-fff/CocoaPress/filament/_common_.ini

@@ -0,0 +1,56 @@
+[filament:*common*]
+bed_temperature = 0
+bridge_fan_speed = 0
+cooling = 0
+disable_fan_first_layers = 3
+enable_dynamic_fan_speeds = 0
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #3D2113
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 70
+filament_density = 1.2912
+filament_deretract_speed = nil
+filament_diameter = 22.66
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = Cocoa Press
+filament_wipe = 1
+first_layer_bed_temperature = 0
+first_layer_temperature = 0
+full_fan_speed_layer = 0
+idle_temperature = nil
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+overhang_fan_speed_0 = 0
+overhang_fan_speed_1 = 0
+overhang_fan_speed_2 = 0
+overhang_fan_speed_3 = 0
+slowdown_below_layer_time = 5
+start_filament_gcode = "; Filament gcode\n"
+

profile_sources/non-prusa-fff/CocoaPress/metadata.json

@@ -0,0 +1,105 @@
+{
+  "repo": {
+    "id": "non-prusa-fff",
+    "name": "Other FFF",
+    "description": "FFF Printers by other vendors",
+    "visibility": ""
+  },
+  "vendor": "CocoaPress",
+  "version": "3.0.0",
+  "index_name": "CocoaPress.idx",
+  "section_order": [
+    {
+      "type": "vendor",
+      "name": "vendor",
+      "path": "vendor/vendor.ini"
+    },
+    {
+      "type": "printer_model",
+      "name": "Cocoa_Press",
+      "path": "printer_model/Cocoa_Press.ini"
+    },
+    {
+      "type": "printer_model",
+      "name": "Cocoa_Press2",
+      "path": "printer_model/Cocoa_Press2.ini"
+    },
+    {
+      "type": "print",
+      "name": "Cocoa Press (0.5mm layerheight)",
+      "path": "print/Cocoa Press (0.5mm layerheight).ini"
+    },
+    {
+      "type": "print",
+      "name": "Cocoa Press (1.0mm layerheight)",
+      "path": "print/Cocoa Press (1.0mm layerheight).ini"
+    },
+    {
+      "type": "print",
+      "name": "Cocoa Press 2 (0.5mm layerheight)",
+      "path": "print/Cocoa Press 2 (0.5mm layerheight).ini"
+    },
+    {
+      "type": "print",
+      "name": "Cocoa Press 2 (1.0mm layerheight)",
+      "path": "print/Cocoa Press 2 (1.0mm layerheight).ini"
+    },
+    {
+      "type": "filament",
+      "name": "*common*",
+      "path": "filament/_common_.ini"
+    },
+    {
+      "type": "filament",
+      "name": "Cocoa Press Chocolates",
+      "path": "filament/Cocoa Press Chocolates.ini"
+    },
+    {
+      "type": "printer",
+      "name": "*CCP1 0.8mm*",
+      "path": "printer/_CCP1 0.8mm_.ini"
+    },
+    {
+      "type": "printer",
+      "name": "*CCP1 1.6mm*",
+      "path": "printer/_CCP1 1.6mm_.ini"
+    },
+    {
+      "type": "printer",
+      "name": "*CCP2 0.8mm*",
+      "path": "printer/_CCP2 0.8mm_.ini"
+    },
+    {
+      "type": "printer",
+      "name": "*CCP2 1.6mm*",
+      "path": "printer/_CCP2 1.6mm_.ini"
+    },
+    {
+      "type": "printer",
+      "name": "Cocoa Press\uff5c0.8mm",
+      "path": "printer/Cocoa Press\uff5c0.8mm.ini"
+    },
+    {
+      "type": "printer",
+      "name": "Cocoa Press\uff5c1.6mm",
+      "path": "printer/Cocoa Press\uff5c1.6mm.ini"
+    },
+    {
+      "type": "printer",
+      "name": "Cocoa Press 2\uff5c0.8mm",
+      "path": "printer/Cocoa Press 2\uff5c0.8mm.ini"
+    },
+    {
+      "type": "printer",
+      "name": "Cocoa Press 2\uff5c1.6mm",
+      "path": "printer/Cocoa Press 2\uff5c1.6mm.ini"
+    }
+  ],
+  "asset_paths": [
+    "CocoaPress_CCP2.png",
+    "CocoaPress_MiniChef.png",
+    "cocoapress2_PS_Bed_Texture.svg",
+    "minichef_bed.stl",
+    "minichef_texture.svg"
+  ]
+}

profile_sources/non-prusa-fff/CocoaPress/print/Cocoa Press (0.5mm layerheight).ini

@@ -0,0 +1,174 @@
+[print:Cocoa Press (0.5mm layerheight)]
+inherits = 
+avoid_crossing_curled_overhangs = 0
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 2
+bottom_solid_min_thickness = 0
+bridge_acceleration = 1500
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_separation = 0
+brim_type = outer_only
+brim_width = 0
+compatible_printers = "Cocoa Press｜0.8mm"
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_COCOA_PRESS.*/ and printer_notes=~/.*PRINTER_MATERIAL_PASTE.*/ and nozzle_diameter[0]==0.8
+complete_objects = 0
+default_acceleration = 1500
+dont_support_bridges = 1
+draft_shield = disabled
+elefant_foot_compensation = 0
+enable_dynamic_overhang_speeds = 1
+external_perimeter_acceleration = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extra_perimeters_on_overhangs = 0
+extrusion_width = 0
+fill_angle = 45
+fill_density = 25%
+fill_pattern = grid
+first_layer_acceleration = 1500
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 15
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 0
+gap_fill_speed = 0
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = "(;PAUSE_PRINT)(\\n|\\r\\n|\\r)(.*?)(M117)";"\\n;MOVE_BEFORE_PAUSE\\n;PAUSED_PRINT_MACRO\\n;END_MOVE_BEFORE_PAUSE\\n$1$2M0";r;"Pause command allows you to get a full screen message.";"(;PAUSED_PRINT_MACRO)(.*?)(\\n|\\r\\n|\\r)";"\\nM83;\\nG1 E-.2 F400;\\nG91;\\nG0 Z10;\\nG90;\\nM83;\\nG0 X70 Y135 F90000;\\nM17;\\n";r;"The second half of the \"manual pause\" is in the custom g-code box in Printer Settings."
+infill_acceleration = 1500
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_overlap = 50%
+infill_speed = 40
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.5
+max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 0
+min_bead_width = 85%
+min_feature_size = 25%
+min_skirt_length = 0
+mmu_segmented_region_max_width = 0
+notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[initial_tool]}n_{print_time}_{round(total_weight)}g.gcode
+overhang_speed_0 = 12
+overhang_speed_1 = 15
+overhang_speed_2 = 20
+overhang_speed_3 = 25
+overhangs = 1
+perimeter_acceleration = 1500
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_generator = arachne
+perimeter_speed = 35
+perimeters = 2
+post_process = 
+print_settings_id = 0.5mm Speed2
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = rear
+single_extruder_multi_material_priming = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 0
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 20
+solid_infill_acceleration = 0
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 40
+spiral_vase = 0
+staggered_inner_seams = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 0
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = -1
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = honeycomb
+support_material_spacing = 5
+support_material_speed = 25
+support_material_style = organic
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+support_tree_angle = 40
+support_tree_angle_slow = 25
+support_tree_branch_diameter = 2
+support_tree_branch_diameter_angle = 5
+support_tree_branch_diameter_double_wall = 3
+support_tree_branch_distance = 1
+support_tree_tip_diameter = 0.8
+support_tree_top_rate = 15%
+thick_bridges = 1
+thin_walls = 0
+threads = 12
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0
+top_solid_infill_acceleration = 0
+top_solid_infill_speed = 25
+top_solid_layers = 5
+top_solid_min_thickness = 0
+travel_acceleration = 0
+travel_speed = 100
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_extruder = 0
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0
+

profile_sources/non-prusa-fff/CocoaPress/print/Cocoa Press (1.0mm layerheight).ini

@@ -0,0 +1,174 @@
+[print:Cocoa Press (1.0mm layerheight)]
+inherits =
+avoid_crossing_curled_overhangs = 0
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 1
+bottom_solid_min_thickness = 0
+bridge_acceleration = 1500
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_separation = 0
+brim_type = outer_only
+brim_width = 0
+compatible_printers = "Cocoa Press｜1.6mm"
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_COCOA_PRESS.*/ and printer_notes=~/.*PRINTER_MATERIAL_PASTE.*/ and nozzle_diameter[0]==1.6
+complete_objects = 0
+default_acceleration = 1500
+dont_support_bridges = 1
+draft_shield = disabled
+elefant_foot_compensation = 0
+enable_dynamic_overhang_speeds = 1
+external_perimeter_acceleration = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extra_perimeters_on_overhangs = 0
+extrusion_width = 0
+fill_angle = 45
+fill_density = 25%
+fill_pattern = grid
+first_layer_acceleration = 1500
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.8
+first_layer_speed = 15
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 0
+gap_fill_speed = 0
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = "(;PAUSE_PRINT)(\\n|\\r\\n|\\r)(.*?)(M117)";"\\n;MOVE_BEFORE_PAUSE\\n;PAUSED_PRINT_MACRO\\n;END_MOVE_BEFORE_PAUSE\\n$1$2M0";r;"Pause command allows you to get a full screen message.";"(;PAUSED_PRINT_MACRO)(.*?)(\\n|\\r\\n|\\r)";"\\nM83;\\nG1 E-.2 F400;\\nG91;\\nG0 Z10;\\nG90;\\nM83;\\nG0 X70 Y135 F90000;\\nM17;\\n";r;"The second half of the \"manual pause\" is in the custom g-code box in Printer Settings."
+infill_acceleration = 1500
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_overlap = 70%
+infill_speed = 40
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 1
+max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 0
+min_bead_width = 85%
+min_feature_size = 25%
+min_skirt_length = 0
+mmu_segmented_region_max_width = 0
+notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[initial_tool]}n_{print_time}_{round(total_weight)}g.gcode
+overhang_speed_0 = 12
+overhang_speed_1 = 15
+overhang_speed_2 = 20
+overhang_speed_3 = 25
+overhangs = 1
+perimeter_acceleration = 1500
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_generator = arachne
+perimeter_speed = 35
+perimeters = 1
+post_process = 
+print_settings_id = 0.5mm Speed2
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = rear
+single_extruder_multi_material_priming = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 0
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 20
+solid_infill_acceleration = 0
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 40
+spiral_vase = 0
+staggered_inner_seams = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 0
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = -1
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = honeycomb
+support_material_spacing = 5
+support_material_speed = 25
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+support_tree_angle = 40
+support_tree_angle_slow = 25
+support_tree_branch_diameter = 2
+support_tree_branch_diameter_angle = 5
+support_tree_branch_diameter_double_wall = 3
+support_tree_branch_distance = 1
+support_tree_tip_diameter = 0.8
+support_tree_top_rate = 15%
+thick_bridges = 1
+thin_walls = 0
+threads = 12
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0
+top_solid_infill_acceleration = 0
+top_solid_infill_speed = 25
+top_solid_layers = 3
+top_solid_min_thickness = 0
+travel_acceleration = 0
+travel_speed = 100
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_cone_angle = 0
+wipe_tower_extra_spacing = 100%
+wipe_tower_extruder = 0
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0
+

profile_sources/non-prusa-fff/CocoaPress/print/Cocoa Press 2 (0.5mm layerheight).ini

@@ -0,0 +1,197 @@
+[print:Cocoa Press 2 (0.5mm layerheight)]
+arc_fitting = emit_center
+automatic_extrusion_widths = 0
+automatic_infill_combination = 0
+automatic_infill_combination_max_layer_height = 100%
+avoid_crossing_curled_overhangs = 0
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bed_temperature_extruder = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 2
+bottom_solid_min_thickness = 0
+bridge_acceleration = 1500
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_separation = 0
+brim_type = outer_only
+brim_width = 0
+compatible_printers = "Cocoa Press 2｜0.8mm"
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_COCOA_PRESS.*/ and printer_notes=~/.*PRINTER_MATERIAL_PASTE.*/ and nozzle_diameter[0]==0.8
+complete_objects = 0
+default_acceleration = 1500
+dont_support_bridges = 1
+draft_shield = disabled
+elefant_foot_compensation = 0
+enable_dynamic_overhang_speeds = 1
+ensure_vertical_shell_thickness = enabled
+external_perimeter_acceleration = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extra_perimeters_on_overhangs = 0
+extrusion_width = 0
+fill_angle = 45
+fill_density = 25%
+fill_pattern = grid
+first_layer_acceleration = 1500
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_infill_speed = 0
+first_layer_speed = 15
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 0
+gap_fill_speed = 0
+gcode_comments = 0
+gcode_label_objects = octoprint
+gcode_resolution = 0.0125
+gcode_substitutions = "(;PAUSE_PRINT)(\\n|\\r\\n|\\r)(.*?)(M117)";"\\n;MOVE_BEFORE_PAUSE\\n;PAUSED_PRINT_MACRO\\n;END_MOVE_BEFORE_PAUSE\\n$1$2M0";r;"Pause command allows you to get a full screen message.";"(;PAUSED_PRINT_MACRO)(.*?)(\\n|\\r\\n|\\r)";"\\nM83;\\nG1 E-.2 F400;\\nG91;\\nG0 Z10;\\nG90;\\nM83;\\nG0 X70 Y135 F90000;\\nM17;\\n";r;"The second half of the \"manual pause\" is in the custom g-code box in Printer Settings."
+infill_acceleration = 1500
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_overlap = 50%
+infill_speed = 40
+inherits = Cocoa Press (0.5mm layerheight)
+interface_shells = 0
+interlocking_beam = 0
+interlocking_beam_layer_count = 2
+interlocking_beam_width = 0.8
+interlocking_boundary_avoidance = 2
+interlocking_depth = 2
+interlocking_orientation = 22.5
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.5
+max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 0
+min_bead_width = 85%
+min_feature_size = 25%
+min_skirt_length = 0
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE
+only_one_perimeter_first_layer = 0
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[initial_tool]}n_{print_time}_{round(total_weight)}g.gcode
+over_bridge_speed = 0
+overhang_speed_0 = 12
+overhang_speed_1 = 15
+overhang_speed_2 = 20
+overhang_speed_3 = 25
+overhangs = 1
+perimeter_acceleration = 1500
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_generator = arachne
+perimeter_speed = 35
+perimeters = 2
+post_process = 
+print_settings_id = 0.5mm Speed2
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+scarf_seam_entire_loop = 0
+scarf_seam_length = 20
+scarf_seam_max_segment_length = 1
+scarf_seam_on_inner_perimeters = 0
+scarf_seam_only_on_smooth = 1
+scarf_seam_placement = nowhere
+scarf_seam_start_height = 0%
+seam_gap_distance = 15%
+seam_position = rear
+single_extruder_multi_material_priming = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 0
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 20
+solid_infill_acceleration = 0
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 40
+spiral_vase = 0
+staggered_inner_seams = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 0
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = -1
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = honeycomb
+support_material_spacing = 5
+support_material_speed = 25
+support_material_style = organic
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+support_tree_angle = 40
+support_tree_angle_slow = 25
+support_tree_branch_diameter = 2
+support_tree_branch_diameter_angle = 5
+support_tree_branch_diameter_double_wall = 3
+support_tree_branch_distance = 1
+support_tree_tip_diameter = 0.8
+support_tree_top_rate = 15%
+thick_bridges = 1
+thin_walls = 0
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0
+top_one_perimeter_type = none
+top_solid_infill_acceleration = 0
+top_solid_infill_speed = 25
+top_solid_layers = 5
+top_solid_min_thickness = 0
+travel_acceleration = 0
+travel_speed = 100
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_tower = 0
+wipe_tower_acceleration = 0
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_cone_angle = 0
+wipe_tower_extra_flow = 100%
+wipe_tower_extra_spacing = 100%
+wipe_tower_extruder = 0
+wipe_tower_no_sparse_layers = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+

profile_sources/non-prusa-fff/CocoaPress/print/Cocoa Press 2 (1.0mm layerheight).ini

@@ -0,0 +1,197 @@
+[print:Cocoa Press 2 (1.0mm layerheight)]
+arc_fitting = emit_center
+automatic_extrusion_widths = 0
+automatic_infill_combination = 0
+automatic_infill_combination_max_layer_height = 100%
+avoid_crossing_curled_overhangs = 0
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bed_temperature_extruder = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 2
+bottom_solid_min_thickness = 0
+bridge_acceleration = 1500
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_separation = 0
+brim_type = outer_only
+brim_width = 0
+compatible_printers = "Cocoa Press 2｜1.6mm"
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_COCOA_PRESS.*/ and printer_notes=~/.*PRINTER_MATERIAL_PASTE.*/ and nozzle_diameter[0]==1.6
+complete_objects = 0
+default_acceleration = 1500
+dont_support_bridges = 1
+draft_shield = disabled
+elefant_foot_compensation = 0
+enable_dynamic_overhang_speeds = 1
+ensure_vertical_shell_thickness = enabled
+external_perimeter_acceleration = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extra_perimeters_on_overhangs = 0
+extrusion_width = 0
+fill_angle = 45
+fill_density = 25%
+fill_pattern = grid
+first_layer_acceleration = 1500
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_infill_speed = 0
+first_layer_speed = 15
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 0
+gap_fill_speed = 0
+gcode_comments = 0
+gcode_label_objects = octoprint
+gcode_resolution = 0.0125
+gcode_substitutions = "(;PAUSE_PRINT)(\\n|\\r\\n|\\r)(.*?)(M117)";"\\n;MOVE_BEFORE_PAUSE\\n;PAUSED_PRINT_MACRO\\n;END_MOVE_BEFORE_PAUSE\\n$1$2M0";r;"Pause command allows you to get a full screen message.";"(;PAUSED_PRINT_MACRO)(.*?)(\\n|\\r\\n|\\r)";"\\nM83;\\nG1 E-.2 F400;\\nG91;\\nG0 Z10;\\nG90;\\nM83;\\nG0 X70 Y135 F90000;\\nM17;\\n";r;"The second half of the \"manual pause\" is in the custom g-code box in Printer Settings."
+infill_acceleration = 1500
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_overlap = 50%
+infill_speed = 40
+inherits = Cocoa Press (0.5mm layerheight)
+interface_shells = 0
+interlocking_beam = 0
+interlocking_beam_layer_count = 2
+interlocking_beam_width = 0.8
+interlocking_boundary_avoidance = 2
+interlocking_depth = 2
+interlocking_orientation = 22.5
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 1.0
+max_print_speed = 80
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 0
+min_bead_width = 85%
+min_feature_size = 25%
+min_skirt_length = 0
+mmu_segmented_region_interlocking_depth = 0
+mmu_segmented_region_max_width = 0
+notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE
+only_one_perimeter_first_layer = 0
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[initial_tool]}n_{print_time}_{round(total_weight)}g.gcode
+over_bridge_speed = 0
+overhang_speed_0 = 12
+overhang_speed_1 = 15
+overhang_speed_2 = 20
+overhang_speed_3 = 25
+overhangs = 1
+perimeter_acceleration = 1500
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_generator = arachne
+perimeter_speed = 35
+perimeters = 2
+post_process = 
+print_settings_id = 0.5mm Speed2
+raft_contact_distance = 0.1
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+scarf_seam_entire_loop = 0
+scarf_seam_length = 20
+scarf_seam_max_segment_length = 1
+scarf_seam_on_inner_perimeters = 0
+scarf_seam_only_on_smooth = 1
+scarf_seam_placement = nowhere
+scarf_seam_start_height = 0%
+seam_gap_distance = 15%
+seam_position = rear
+single_extruder_multi_material_priming = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 0
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 20
+solid_infill_acceleration = 0
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 40
+spiral_vase = 0
+staggered_inner_seams = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 0
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = -1
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = honeycomb
+support_material_spacing = 5
+support_material_speed = 25
+support_material_style = organic
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+support_tree_angle = 40
+support_tree_angle_slow = 25
+support_tree_branch_diameter = 2
+support_tree_branch_diameter_angle = 5
+support_tree_branch_diameter_double_wall = 3
+support_tree_branch_distance = 1
+support_tree_tip_diameter = 0.8
+support_tree_top_rate = 15%
+thick_bridges = 1
+thin_walls = 0
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0
+top_one_perimeter_type = none
+top_solid_infill_acceleration = 0
+top_solid_infill_speed = 25
+top_solid_layers = 5
+top_solid_min_thickness = 0
+travel_acceleration = 0
+travel_speed = 100
+travel_speed_z = 0
+wall_distribution_count = 1
+wall_transition_angle = 10
+wall_transition_filter_deviation = 25%
+wall_transition_length = 100%
+wipe_tower = 0
+wipe_tower_acceleration = 0
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_cone_angle = 0
+wipe_tower_extra_flow = 100%
+wipe_tower_extra_spacing = 100%
+wipe_tower_extruder = 0
+wipe_tower_no_sparse_layers = 0
+wipe_tower_width = 60
+xy_size_compensation = 0
+

profile_sources/non-prusa-fff/CocoaPress/printer/Cocoa Press 2｜0.8mm.ini

@@ -0,0 +1,9 @@
+[printer:Cocoa Press 2｜0.8mm]
+inherits = *CCP2 0.8mm*
+default_filament_profile = "Cocoa Press Chocolates"
+printer_notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE\nNO_TEMPLATES
+gcode_flavor = klipper
+extruder_clearance_height = 60
+extruder_clearance_radius = 65
+printer_model = Cocoa_Press2
+

profile_sources/non-prusa-fff/CocoaPress/printer/Cocoa Press 2｜1.6mm.ini

@@ -0,0 +1,9 @@
+[printer:Cocoa Press 2｜1.6mm]
+inherits = *CCP2 1.6mm*
+default_filament_profile = "Cocoa Press Chocolates"
+printer_notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE\nNO_TEMPLATES
+gcode_flavor = klipper
+extruder_clearance_height = 60
+extruder_clearance_radius = 65
+printer_model = Cocoa_Press2
+

profile_sources/non-prusa-fff/CocoaPress/printer/Cocoa Press｜0.8mm.ini

@@ -0,0 +1,9 @@
+[printer:Cocoa Press｜0.8mm]
+inherits = *CCP1 0.8mm*
+default_filament_profile = "Cocoa Press Chocolates"
+printer_notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE\nNO_TEMPLATES
+gcode_flavor = marlin2
+extruder_clearance_height = 60
+extruder_clearance_radius = 65
+printer_model = Cocoa_Press
+

profile_sources/non-prusa-fff/CocoaPress/printer/Cocoa Press｜1.6mm.ini

@@ -0,0 +1,9 @@
+[printer:Cocoa Press｜1.6mm]
+inherits = *CCP1 1.6mm*
+default_filament_profile = "Cocoa Press Chocolates"
+printer_notes = PRINTER_VENDOR_COCOA_PRESS\nPRINTER_MODEL_MINICHEF\nPRINTER_MATERIAL_PASTE\nNO_TEMPLATES
+gcode_flavor = marlin2
+extruder_clearance_height = 60
+extruder_clearance_radius = 65
+printer_model = Cocoa_Press
+

profile_sources/non-prusa-fff/CocoaPress/printer/_CCP1 0.8mm_.ini

@@ -0,0 +1,74 @@
+[printer:*CCP1 0.8mm*]
+printer_variant = CCP1 0.8
+default_print_profile = 0.5
+autoemit_temperature_commands = 0
+bed_shape = 0x0,140x0,140x150,0x150
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n\n
+between_objects_gcode = 
+color_change_gcode = ;BEFORE_COLOR_CHANGE\n\nM83; use relative extrusion for extruder.\nG1 E-.2 F400 ;minor retraction to keep ooze contained.\n\nG60; save position\n\n;move the bed down 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG0 X70 Y5; move to front for user to swap core.\nM17; enable steppers so that the user can change cores without having the extruder or bed slip or move as easily.\n\nM0 Perform core swap now. Press OK when loaded.;\n\n; pause message, lazy edition.\nM117 Preheating core. (waiting 15m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 14m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 13m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 12m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 11m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 10m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 9m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 8m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 7m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 6m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 5m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 4m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 3m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 2m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 1m);\nG4 S60; pause delay so it's on screen \nM0 Press "OK" to continue print. Have the spatula ready.;\n\n;move the bed up 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG1 E.06 F900 ;extrude a lil bit.\nG92 E0 ; set extruder pos to zero\n\n; restore position\nG61; \n\n;AFTER_COLOR_CHANGE
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+deretract_speed = 15
+end_gcode = print_end    ;end script from macro\nG91 ; set to relative\nG0 Z15; ; move 15mm down\nG90 ; absolute positioning again\nG0 X70 Y135\nM84
+extra_loading_move = -2
+extruder_colour = #F27121
+extruder_offset = 0x0
+high_current_on_filament_swap = 0
+host_type = octoprint
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = time_estimate_only
+machine_max_acceleration_e = 1500
+machine_max_acceleration_extruding = 1500
+machine_max_acceleration_retracting = 1500
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1500
+machine_max_acceleration_y = 1500
+machine_max_acceleration_z = 500
+machine_max_feedrate_e = 120
+machine_max_feedrate_x = 500
+machine_max_feedrate_y = 500
+machine_max_feedrate_z = 12
+machine_max_jerk_e = 2.5
+machine_max_jerk_x = 10
+machine_max_jerk_y = 10
+machine_max_jerk_z = 0.2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 0.8
+max_print_height = 150
+min_layer_height = 0.2
+nozzle_diameter = 0.8
+parking_pos_retraction = 92
+pause_print_gcode = ; Start Pause Print\n; This pause GCode is changed in PrusaSlicer via the Print Settings -> Output Options -> G-Code Substititons\n; This is due to how PrusaSlicer inserts the M117 message for pause at the start of any custom GCode in this\n; box.  As such, to soft-park the toolhead, handle retractions, and more, this is done in custom G-Code inj-\n; -ected before this message.  Furthering this, due to a bug in how Marlin handles M117 messages on our di-\n; -splay, we use M0 instead, hence the use of the second G-Code substitution regex.\n; Thank you for understanding.\n\n\nG90; Set absolute coordinate moves\nM83; set extruder relative.\nG61 F15000 XY ; move to last XY position.\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG1 E.6 F300; Purge small amount of Cocoa Core via extruder after pause.\n\nG61 F15000 Z; move to last Z position (10mm offset, probably)\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG92 E0; Set extruder to "zero" so that it's not remembered.\nG1 E.00001 900; very small move to reset feedrate bug.\n
+print_host = 
+printer_settings_id = cocoa_press_minichef_settings_0_8
+printer_technology = FFF
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 3
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 1
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 15
+silent_mode = 0
+single_extruder_multi_material = 0
+start_gcode = M220 S100; set speed to 100%\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\n\nG28; home all axes\nM420 S1; turn back on mesh leveling\nG92 E0 ; set extruder pos to zero\n\n; homing + loading mesh\nG29 O V4 ; try to probe mesh, but skip if already done.\n\nG1 Z1.5 F4500\n\n; Purge Line 1\n\nG1 X131.75 Y148 Z3.2\nG1 X128.625 Y148 Z.5 E.15\nG1 X8.25 Y148 E.25 F900\n\n; Purge Line 2\n\nG1 X8.25 Y145 F900\nG1 X131.25 Y145 E.10538\nG1 X141.75 Y145
+template_custom_gcode = 
+thumbnails = 64x64,400x300
+thumbnails_format = PNG
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0
+

profile_sources/non-prusa-fff/CocoaPress/printer/_CCP1 1.6mm_.ini

@@ -0,0 +1,74 @@
+[printer:*CCP1 1.6mm*]
+printer_variant = CCP1 1.6
+autoemit_temperature_commands = 0
+bed_shape = 0x0,140x0,140x150,0x150
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n\n
+between_objects_gcode = 
+color_change_gcode = ;BEFORE_COLOR_CHANGE\n\nM83; use relative extrusion for extruder.\nG1 E-.2 F400 ;minor retraction to keep ooze contained.\n\nG60; save position\n\n;move the bed down 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG0 X70 Y5; move to front for user to swap core.\nM17; enable steppers so that the user can change cores without having the extruder or bed slip or move as easily.\n\nM0 Perform core swap now. Press OK when loaded.;\n\n; pause message, lazy edition.\nM117 Preheating core. (waiting 15m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 14m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 13m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 12m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 11m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 10m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 9m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 8m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 7m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 6m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 5m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 4m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 3m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 2m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 1m);\nG4 S60; pause delay so it's on screen \nM0 Press "OK" to continue print. Have the spatula ready.;\n\n;move the bed up 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG1 E.06 F900 ;extrude a lil bit.\nG92 E0 ; set extruder pos to zero\n\nG61; restore start position\n;AFTER_COLOR_CHANGE
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_print_profile = 1.0
+deretract_speed = 15
+end_gcode = print_end    ;end script from macro\nG91 ; set to relative\nG0 Z15; ; move 15mm down\nG90 ; absolute positioning again\nG0 X70 Y135\nM84
+extra_loading_move = -2
+extruder_colour = #F27121
+extruder_offset = 0x0
+high_current_on_filament_swap = 0
+host_type = octoprint
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = time_estimate_only
+machine_max_acceleration_e = 1500
+machine_max_acceleration_extruding = 1500
+machine_max_acceleration_retracting = 1500
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1500
+machine_max_acceleration_y = 1500
+machine_max_acceleration_z = 500
+machine_max_feedrate_e = 120
+machine_max_feedrate_x = 500
+machine_max_feedrate_y = 500
+machine_max_feedrate_z = 12
+machine_max_jerk_e = 2.5
+machine_max_jerk_x = 10
+machine_max_jerk_y = 10
+machine_max_jerk_z = 0.2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 1.6
+max_print_height = 150
+min_layer_height = 0.2
+nozzle_diameter = 1.6
+parking_pos_retraction = 92
+pause_print_gcode = ; Start Pause Print\n; This pause GCode is changed in PrusaSlicer via the Print Settings -> Output Options -> G-Code Substititons\n; This is due to how PrusaSlicer inserts the M117 message for pause at the start of any custom GCode in this\n; box.  As such, to soft-park the toolhead, handle retractions, and more, this is done in custom G-Code inj-\n; -ected before this message.  Furthering this, due to a bug in how Marlin handles M117 messages on our di-\n; -splay, we use M0 instead, hence the use of the second G-Code substitution regex.\n; Thank you for understanding.\n\n\nG90; Set absolute coordinate moves\nM83; set extruder relative.\nG61 F15000 XY ; move to last XY position.\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG1 E.6 F300; Purge small amount of Cocoa Core via extruder after pause.\n\nG61 F15000 Z; move to last Z position (10mm offset, probably)\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG92 E0; Set extruder to "zero" so that it's not remembered.\nG1 E.00001 900; very small move to reset feedrate bug.\n
+print_host = 
+printer_settings_id = cocoa_press_minichef_settings_1_6
+printer_technology = FFF
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 3
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 1
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 15
+silent_mode = 0
+single_extruder_multi_material = 0
+start_gcode = M220 S100; set speed to 100%\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\n\nG28; home all axes\nM420 S1; turn back on mesh leveling\nG92 E0 ; set extruder pos to zero\n\n; homing loading mesh\nG29 O V4; try to probe mesh, but skip if already done.\n\nG1 Z1.5 F4500\n\n; Purge Line\n\nG1 X145 Y 145\nG1 Z1 ; small z-hop to avoid potentially big purge getting caught.\nG1 E1.25 F450\nG1 X5 Y145 E.33109 F900
+template_custom_gcode = 
+thumbnails = 64x64,400x300
+thumbnails_format = PNG
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0
+

profile_sources/non-prusa-fff/CocoaPress/printer/_CCP2 0.8mm_.ini

@@ -0,0 +1,83 @@
+[printer:*CCP2 0.8mm*]
+autoemit_temperature_commands = 0
+bed_shape = 0x0,135x0,135x135,0x135
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n\n
+between_objects_gcode = 
+binary_gcode = 0
+color_change_gcode = ;BEFORE_COLOR_CHANGE\n\nM83; use relative extrusion for extruder.\nG1 E-.2 F400 ;minor retraction to keep ooze contained.\n\nG60; save position\n\n;move the bed down 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG0 X70 Y5; move to front for user to swap core.\nM17; enable steppers so that the user can change cores without having the extruder or bed slip or move as easily.\n\nM0 Perform core swap now. Press OK when loaded.;\n\n; pause message, lazy edition.\nM117 Preheating core. (waiting 15m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 14m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 13m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 12m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 11m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 10m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 9m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 8m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 7m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 6m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 5m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 4m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 3m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 2m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 1m);\nG4 S60; pause delay so it's on screen \nM0 Press "OK" to continue print. Have the spatula ready.;\n\n;move the bed up 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG1 E.06 F900 ;extrude a lil bit.\nG92 E0 ; set extruder pos to zero\n\n; restore position\nG61; \n\n;AFTER_COLOR_CHANGE
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = "Cocoa Press Chocolates"
+default_print_profile = 0.5
+deretract_speed = 30
+end_gcode = print_end    ;end script from macro\nG91 ; set to relative\nG0 Z15; ; move 15mm down\nG90 ; absolute positioning again\nG0 X70 Y135\nM84
+extra_loading_move = -2
+extruder_colour = #F27121
+extruder_offset = 0x0
+high_current_on_filament_swap = 0
+host_type = octoprint
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = time_estimate_only
+machine_max_acceleration_e = 1500
+machine_max_acceleration_extruding = 1500
+machine_max_acceleration_retracting = 1500
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1500
+machine_max_acceleration_y = 1500
+machine_max_acceleration_z = 500
+machine_max_feedrate_e = 120
+machine_max_feedrate_x = 500
+machine_max_feedrate_y = 500
+machine_max_feedrate_z = 12
+machine_max_jerk_e = 2.5
+machine_max_jerk_x = 10
+machine_max_jerk_y = 10
+machine_max_jerk_z = 0.2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 0.8
+max_print_height = 150
+min_layer_height = 0.2
+multimaterial_purging = 140
+nozzle_diameter = 0.8
+nozzle_high_flow = 0
+parking_pos_retraction = 92
+pause_print_gcode = ; Start Pause Print\n; This pause GCode is changed in PrusaSlicer via the Print Settings -> Output Options -> G-Code Substititons\n; This is due to how PrusaSlicer inserts the M117 message for pause at the start of any custom GCode in this\n; box.  As such, to soft-park the toolhead, handle retractions, and more, this is done in custom G-Code inj-\n; -ected before this message.  Furthering this, due to a bug in how Marlin handles M117 messages on our di-\n; -splay, we use M0 instead, hence the use of the second G-Code substitution regex.\n; Thank you for understanding.\n\n\nG90; Set absolute coordinate moves\nM83; set extruder relative.\nG61 F15000 XY ; move to last XY position.\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG1 E.6 F300; Purge small amount of Cocoa Core via extruder after pause.\n\nG61 F15000 Z; move to last Z position (10mm offset, probably)\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG92 E0; Set extruder to "zero" so that it's not remembered.\nG1 E.00001 900; very small move to reset feedrate bug.\n
+prefer_clockwise_movements = 0
+print_host = 
+printer_settings_id = cocoa_press_minichef2_settings_0_8
+printer_technology = FFF
+printer_variant = CCP2 0.8
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 3
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0.5
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+silent_mode = 0
+single_extruder_multi_material = 0
+start_gcode = G90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\n\nG28; home all axes\nG92 E0 ; set extruder pos to zero\n\n; loading mesh\nBED_MESH_PROFILE LOAD=default\n\nG1 Z1.5 F4500\n\n\n; G0 X{first_layer_print_min[0]-4.33} Y{first_layer_print_min[1]-12.5}\n; G0 Z0.8\n; G1 X{first_layer_print_min[0]+30} Y{first_layer_print_min[1]-12.5} E.75 F300 ; R-5.0 E3.0 F15\n\n\nG1 Z1.5 F4500\n\n; Purge Line 1\n\nG1 X131.75 Y133 Z3.2\nG1 X128.625 Y133 Z.5 E.15\nG1 X8.25 Y133 E.25 F900\n\n; Purge Line 2\n\nG1 X8.25 Y130 F900\nG1 X131.25 Y130 E.10538\n;G1 X141.75 Y130
+template_custom_gcode = 
+thumbnails = 64x64/PNG, 400x300/PNG
+thumbnails_format = PNG
+toolchange_gcode = 
+travel_lift_before_obstacle = 0
+travel_max_lift = 0
+travel_ramping_lift = 0
+travel_slope = 0
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0
+

profile_sources/non-prusa-fff/CocoaPress/printer/_CCP2 1.6mm_.ini

@@ -0,0 +1,82 @@
+[printer:*CCP2 1.6mm*]
+autoemit_temperature_commands = 0
+bed_shape = 0x0,135x0,135x135,0x135
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n\n
+between_objects_gcode = 
+binary_gcode = 0
+color_change_gcode = ;BEFORE_COLOR_CHANGE\n\nM83; use relative extrusion for extruder.\nG1 E-.2 F400 ;minor retraction to keep ooze contained.\n\nG60; save position\n\n;move the bed down 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG0 X70 Y5; move to front for user to swap core.\nM17; enable steppers so that the user can change cores without having the extruder or bed slip or move as easily.\n\nM0 Perform core swap now. Press OK when loaded.;\n\n; pause message, lazy edition.\nM117 Preheating core. (waiting 15m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 14m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 13m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 12m);\nG4 S60; pause delay so it's on screen\nM117 Preheating core. (waiting 11m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 10m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 9m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 8m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 7m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 6m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 5m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 4m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 3m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 2m);\nG4 S60; pause delay so it's on screen \nM117 Preheating core. (waiting 1m);\nG4 S60; pause delay so it's on screen \nM0 Press "OK" to continue print. Have the spatula ready.;\n\n;move the bed up 10mm\nG91; set to relative positioning\nG0 Z10;\nG90;\nM83; extruder relative motion.\n\nG1 E.06 F900 ;extrude a lil bit.\nG92 E0 ; set extruder pos to zero\n\n; restore position\nG61; \n\n;AFTER_COLOR_CHANGE
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_print_profile = 0.5
+deretract_speed = 30
+end_gcode = print_end    ;end script from macro\nG91 ; set to relative\nG0 Z15; ; move 15mm down\nG90 ; absolute positioning again\nG0 X70 Y135\nM84
+extra_loading_move = -2
+extruder_colour = #F27121
+extruder_offset = 0x0
+high_current_on_filament_swap = 0
+host_type = octoprint
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = time_estimate_only
+machine_max_acceleration_e = 1500
+machine_max_acceleration_extruding = 1500
+machine_max_acceleration_retracting = 1500
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1500
+machine_max_acceleration_y = 1500
+machine_max_acceleration_z = 500
+machine_max_feedrate_e = 120
+machine_max_feedrate_x = 500
+machine_max_feedrate_y = 500
+machine_max_feedrate_z = 12
+machine_max_jerk_e = 2.5
+machine_max_jerk_x = 10
+machine_max_jerk_y = 10
+machine_max_jerk_z = 0.2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 1.6
+max_print_height = 150
+min_layer_height = 0.2
+multimaterial_purging = 140
+nozzle_diameter = 1.6
+nozzle_high_flow = 0
+parking_pos_retraction = 92
+pause_print_gcode = ; Start Pause Print\n; This pause GCode is changed in PrusaSlicer via the Print Settings -> Output Options -> G-Code Substititons\n; This is due to how PrusaSlicer inserts the M117 message for pause at the start of any custom GCode in this\n; box.  As such, to soft-park the toolhead, handle retractions, and more, this is done in custom G-Code inj-\n; -ected before this message.  Furthering this, due to a bug in how Marlin handles M117 messages on our di-\n; -splay, we use M0 instead, hence the use of the second G-Code substitution regex.\n; Thank you for understanding.\n\n\nG90; Set absolute coordinate moves\nM83; set extruder relative.\nG61 F15000 XY ; move to last XY position.\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG1 E.6 F300; Purge small amount of Cocoa Core via extruder after pause.\n\nG61 F15000 Z; move to last Z position (10mm offset, probably)\nM400; wait for move to finish.\nG4 P100; small delay (100ms) to get around desync issues.\n\nG92 E0; Set extruder to "zero" so that it's not remembered.\nG1 E.00001 900; very small move to reset feedrate bug.\n
+prefer_clockwise_movements = 0
+print_host = 
+printer_settings_id = cocoa_press_minichef2_settings_1_6
+printer_technology = FFF
+printer_variant = CCP2 1.6
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 3
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0.5
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+silent_mode = 0
+single_extruder_multi_material = 0
+start_gcode = G90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\n\nG28; home all axes\nG92 E0 ; set extruder pos to zero\n\n; loading mesh\nBED_MESH_PROFILE LOAD=default\n\nG1 Z1.5 F4500\n\n\n; G0 X{first_layer_print_min[0]-4.33} Y{first_layer_print_min[1]-12.5}\n; G0 Z0.8\n; G1 X{first_layer_print_min[0]+30} Y{first_layer_print_min[1]-12.5} E.75 F300 ; R-5.0 E3.0 F15\n\n\nG1 Z1.5 F4500\n\n; Purge Line 1\n\nG1 X131.75 Y133 Z3.2\nG1 X128.625 Y133 Z.5 E.15\nG1 X8.25 Y133 E.25 F900\n\n; Purge Line 2\n\nG1 X8.25 Y130 F900\nG1 X131.25 Y130 E.10538\n;G1 X141.75 Y130
+template_custom_gcode = 
+thumbnails = 64x64/PNG, 400x300/PNG
+thumbnails_format = PNG
+toolchange_gcode = 
+travel_lift_before_obstacle = 0
+travel_max_lift = 0
+travel_ramping_lift = 0
+travel_slope = 0
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0
+

profile_sources/non-prusa-fff/CocoaPress/printer_model/Cocoa_Press.ini

@@ -0,0 +1,9 @@
+[printer_model:Cocoa_Press]
+name = Cocoa Press
+variants = CCP1 0.8; CCP1 1.6
+technology = FFF
+bed_model = minichef_bed.stl 
+bed_texture = minichef_texture.svg
+default_materials = Cocoa Press Chocolates;
+thumbnail = CocoaPress_MiniChef.png
+

profile_sources/non-prusa-fff/CocoaPress/printer_model/Cocoa_Press2.ini

@@ -0,0 +1,9 @@
+[printer_model:Cocoa_Press2]
+name = Cocoa Press 2
+variants = CCP2 0.8; CCP2 1.6
+technology = FFF
+bed_model = minichef_bed.stl 
+bed_texture = cocoapress2_PS_Bed_Texture.svg
+default_materials = Cocoa Press Chocolates;
+thumbnail = CocoaPress_CCP2.png
+

profile_sources/non-prusa-fff/CocoaPress/vendor.idx

@@ -0,0 +1,13 @@
+min_slic3r_version = 2.9.1-alpha0
+3.0.0 Added Cocoa Press 2.
+2.1.0 Extruder clearance moved to printer settings.
+min_slic3r_version = 2.8.0-alpha0
+2.0.0 Updated for PS2.8.0.
+min_slic3r_version = 2.7.9
+min_slic3r_version = 2.6.0-alpha2
+1.0.5 Hotfix for 2.7.2 color change, as well as ramping prime line to reduce initial blob
+1.0.4 Added proper pause and core change GCode that seems somewhat reliable.
+1.0.3 Swap purge direction for 1.6 nozzle to reduce dwelling time.
+1.0.2 Removed invalid compatible_print condition.
+1.0.1 Swapped Pause GCode, Fixed Chocolate Colors, Resolved Output Format issue from Inheriting Keyword Typo
+1.0.0 Initial

profile_sources/non-prusa-fff/CocoaPress/vendor/vendor.ini

@@ -0,0 +1,18 @@
+[vendor]
+repo_id = non-prusa-fff
+# Vendor name will be shown by the Config Wizard.
+name = Cocoa Press
+# Configuration version of this file. Config file will only be installed, if the config_version differs.
+# This means, the server may force the PrusaSlicer configuration to be downgraded.
+config_version = 3.0.0
+# Where to get the updates from?
+config_update_url = https://files.prusa3d.com/wp-content/uploads/repository/PrusaSlicer-settings-master/live/CocoaPress/
+# changelog_url = https://files.prusa3d.com/?latest=slicer-profiles&lng=%1%
+
+# The printer models will be shown by the Configuration Wizard in this order,
+# also the first model installed & the first nozzle installed will be activated after install.
+# Printer model name will be shown by the installation wizard.
+
+# All presets starting with asterisk, for example *common*, are intermediate and they will
+# not make it into the user interface.
+