Initial Profile Sources

profile_sources/non-prusa-fff/Geeetech/print/_High-speed_.ini

@@ -0,0 +1,49 @@
+[print:*High-speed*]
+# Print presets for high-speed printers.
+inherits = *common*
+top_solid_layers = 3
+bottom_solid_layers = 3
+gap_fill_enabled = 0
+default_acceleration = 5000
+perimeter_speed = 230
+external_perimeter_speed = 83%
+solid_infill_speed = 80
+infill_speed = 250
+top_solid_infill_speed =100%
+support_material_speed = 100
+support_material_interface_speed = 50%
+brim_speed = 30%
+bridge_speed = 180
+bridge_speed_internal = 120%
+overhangs_speed = 120%
+gap_fill_speed = 100
+gap_fill_flow_match_perimeter = 0
+thin_walls_speed = 100%
+ironing_speed = 75%
+travel_speed = 260
+travel_speed_z = 0
+first_layer_min_speed = 0
+first_layer_speed = 30
+first_layer_infill_speed = 0
+first_layer_speed_over_raft = 30
+small_perimeter_speed = 65%
+max_print_speed = 300
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+small_perimeter_min_length = 8
+small_perimeter_max_length = 25.1327
+solid_infill_below_area = 0
+#travel_speed = {if 120<=infill_speed<=200}200{elsif infill_speed>200}infill_speed{else}150{endif}
+#perimeter_speed = {if infill_speed<60}math.ceil(round(infill_speed*0.8){elsif infill_speed>60}math.ceil(round(infill_speed*0.75)){else}60{endif}
+#external_perimeter_speed = {if infill_speed<=60}math.ceil(round(infill_speed*0.5)){else}math.ceil(round(infill_speed*0.75)){endif}
+#solid_infill_speed = {if infill_speed<=60}20{else}math.ceil(round(infill_speed*0.3)){endif}
+#top_solid_infill_speed = {if infill_speed<=60}20{elsif 60<infill_speed<200}math.ceil(round(infill_speed*0.6){elsif 200<=infill_speed<=250}math.ceil(round(infill_speed*0.5){else}math.ceil(round(infill_speed*0.4)){endif}
+#support_material_speed = {if infill_speed<60}math.ceil(round(infill_speed*0.8){elsif infill_speed>60}math.ceil(round(infill_speed*0.5){else}40{endif}
+#bridge_speed = {if infill_speed<=60}math.ceil(round(infill_speed*0.5)){else}math.ceil(round(infill_speed*0.75)){endif}
+#bridge_speed_internal = {if infill_speed<=60}math.ceil(round(infill_speed*1.5)){elsif 60<infill_speed<200}math.ceil(round(infill_speed*1.2){elsif 200<=infill_speed<=250}infill_speed{else}math.ceil(round(infill_speed*0.8)){endif}
+#overhangs_speed = {if infill_speed<=60}infill_speed{elsif 60<infill_speed<200}math.ceil(round(infill_speed*0.9){elsif 200<=infill_speed<=250}math.ceil(round(infill_speed*0.85){else}math.ceil(round(infill_speed*0.8)){endif}
+#gap_fill_speed = {if infill_speed<=60}math.ceil(round(infill_speed*0.3){elsif 60<infill_speed<150}math.ceil(round(infill_speed*0.5){elsif 150<=infill_speed<=200}math.ceil(round(infill_speed*0.6){else}math.ceil(round(infill_speed*0.65)){endif}
+#thin_walls_speed = math.ceil(round(external_perimeter_speed*0.6)
+#ironing_speed =  math.ceil(round(infill_speed*0.5)
+#small_perimeter_speed = math.ceil(round(infill_speed*0.45)
+