Initial Profile Sources

profile_sources/non-prusa-fff/PapapiuLab/filament/Generic ABS @Papapiu.ini

@@ -0,0 +1,49 @@
+[filament:Generic ABS @Papapiu]
+filament_vendor = Generic
+filament_type = ABS
+bed_temperature = 105
+bridge_fan_speed = 30
+cooling = 0
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.98
+fan_always_on = 0
+fan_below_layer_time = 10
+filament_colour = #3A80CA
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cooling_zone_pause = 0
+filament_cost = 18
+filament_density = 1.04
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_speed = 0
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_layer_change = 0
+filament_retract_length = 0.7
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_toolchange_part_fan_speed = 50
+filament_toolchange_temp = 200
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_wipe = 1
+first_layer_bed_temperature = 108
+first_layer_temperature = 248
+full_fan_speed_layer = 0
+max_fan_speed = 30
+min_fan_speed = 20
+min_print_speed = 25
+slowdown_below_layer_time = 10
+start_filament_gcode = ""
+temperature = 243
+

profile_sources/non-prusa-fff/PapapiuLab/filament/Generic PETG @Papapiu.ini

@@ -0,0 +1,45 @@
+[filament:Generic PETG @Papapiu]
+filament_vendor = Generic
+filament_type = PETG
+bed_temperature = 80
+bridge_fan_speed = 100
+cooling = 0
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.94
+fan_always_on = 1
+fan_below_layer_time = 10
+filament_colour = #FF8000
+filament_cost = 20
+filament_density = 1.27
+filament_diameter = 1.75
+filament_enable_toolchange_part_fan = 0
+filament_enable_toolchange_temp = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_speed = 0
+filament_max_volumetric_speed = 11
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_layer_change = 1
+filament_retract_length = 1.2
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_wipe = 1
+first_layer_bed_temperature = 80
+first_layer_temperature = 240
+full_fan_speed_layer = 0
+max_fan_speed = 100
+min_fan_speed = 40
+min_print_speed = 15
+slowdown_below_layer_time = 10
+start_filament_gcode = ""
+temperature = 235
+
+

profile_sources/non-prusa-fff/PapapiuLab/filament/Generic PLA @Papapiu.ini

@@ -0,0 +1,47 @@
+[filament:Generic PLA @Papapiu]
+filament_vendor = Generic
+filament_type = PLA
+bed_temperature = 65
+bridge_fan_speed = 100
+cooling = 0
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 0.89
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #FF3232
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cooling_zone_pause = 0
+filament_cost = 20
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_speed = 0
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_length = 0.6
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_wipe = nil
+first_layer_bed_temperature = 68
+first_layer_temperature = 205
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 15
+start_filament_gcode = ""
+temperature = 195
+

profile_sources/non-prusa-fff/PapapiuLab/filament/Generic TPU @Papapiu.ini

@@ -0,0 +1,82 @@
+[filament:Generic TPU @Papapiu]
+inherits = Generic PLA @Papapiu
+bed_temperature = 30
+bridge_fan_speed = 100
+bridge_internal_fan_speed = -1
+chamber_temperature = 0
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 0
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+external_perimeter_fan_speed = -1
+extrusion_multiplier = 0.89
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #FF00FF
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cooling_zone_pause = 0
+filament_cost = 20
+filament_custom_variables = ""
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_dip_extraction_speed = 70
+filament_dip_insertion_speed = 33
+filament_enable_toolchange_part_fan = 0
+filament_enable_toolchange_temp = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_overlap = 100%
+filament_max_speed = 0
+filament_max_volumetric_speed = 5
+filament_max_wipe_tower_speed = 0
+filament_melt_zone_pause = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "This is a profile for TPU95A. It was tested with Anycubic TPU95A, but most of the economy TPU filaments behave pretty similar.\n\nYou will want to optimize the temperature. Even different colors of the same brand can require 10° more or less.\n\nIf you experience clogs or grinding, reduce the maximum volumetric speed!"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1
+filament_retract_lift = 0.1
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_seam_gap = nil
+filament_shrink = 100%
+filament_skinnydip_distance = 31
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_toolchange_part_fan_speed = 50
+filament_toolchange_temp = 200
+filament_type = FLEX
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_use_fast_skinnydip = 0
+filament_use_skinnydip = 0
+filament_vendor = Generic
+filament_wipe = nil
+filament_wipe_advanced_pigment = 0.5
+filament_wipe_extra_perimeter = nil
+filament_wipe_only_crossing = nil
+filament_wipe_speed = nil
+first_layer_bed_temperature = 30
+first_layer_temperature = 220
+full_fan_speed_layer = 4
+max_fan_speed = 100
+max_speed_reduction = 95%
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 8
+start_filament_gcode = ""
+temperature = 220
+top_fan_speed = -1