mirror of
https://github.com/Santoku-Slicer/Profiles.git
synced 2026-10-01 10:37:17 +00:00
Initial Profile Sources
This commit is contained in:
Dark98
@@ -0,0 +1,11 @@
|
||||
[printer:SV01 0.3 nozzle]
|
||||
inherits = SV01
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV01
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV01 0.6 nozzle]
|
||||
inherits = SV01
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV01
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
[printer:SV01 0.8 nozzle]
|
||||
inherits = SV01
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV01
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
# XXXXXXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV01 PRO---XXX
|
||||
# XXXXXXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV01 PRO 0.3 nozzle]
|
||||
inherits = SV01 PRO
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV01
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV01 PRO 0.6 nozzle]
|
||||
inherits = SV01 PRO
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV01
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,21 @@
|
||||
[printer:SV01 PRO 0.8 nozzle]
|
||||
inherits = SV01 PRO
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV01
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV02 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,47 @@
|
||||
[printer:SV01 PRO]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,280x0,280x240,0x240
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
deretract_speed = 0
|
||||
end_gcode = G1 X5 Y200 F1000 ; \nM104 S0 ; kill extruder temperature\nM140 S0 ; kill bed temperature\nM107; kill fan\nM84 ; disable motors\nM300; beep\n
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #0080FF
|
||||
gcode_flavor = marlin2
|
||||
high_current_on_filament_swap = 0
|
||||
machine_max_acceleration_e = 1000,5000
|
||||
machine_max_acceleration_extruding = 500,1250
|
||||
machine_max_acceleration_retracting = 500,1250
|
||||
machine_max_acceleration_x = 500,1000
|
||||
machine_max_acceleration_y = 500,1000
|
||||
machine_max_acceleration_z = 100,200
|
||||
machine_max_feedrate_e = 25,120
|
||||
machine_max_feedrate_x = 300,200
|
||||
machine_max_feedrate_y = 300,200
|
||||
machine_max_feedrate_z = 5,12
|
||||
machine_max_jerk_e = 5,2.5
|
||||
machine_max_jerk_x = 10,10
|
||||
machine_max_jerk_y = 10,10
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0.32
|
||||
max_print_height = 300
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
remaining_times = 0
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV01 PRO\n
|
||||
retract_layer_change = 0
|
||||
retract_length = 2
|
||||
retract_length_toolchange = 10
|
||||
silent_mode = 0
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
use_relative_e_distances = 0
|
||||
printer_model = SV01 PRO
|
||||
default_print_profile = 0.20mm SPEED @SV01
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,48 @@
|
||||
[printer:SV01]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,280x0,280x240,0x240
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
deretract_speed = 0
|
||||
end_gcode = G1 X5 Y200 F1000 ; \nM104 S0 ; kill extruder temperature\nM140 S0 ; kill bed temperature\nM107; kill fan\nM84 ; disable motors\nM300; beep\n
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #0080FF
|
||||
gcode_flavor = marlin2
|
||||
high_current_on_filament_swap = 0
|
||||
machine_max_acceleration_e = 1000,5000
|
||||
machine_max_acceleration_extruding = 500,1250
|
||||
machine_max_acceleration_retracting = 500,1250
|
||||
machine_max_acceleration_x = 500,1000
|
||||
machine_max_acceleration_y = 500,1000
|
||||
machine_max_acceleration_z = 100,200
|
||||
machine_max_feedrate_e = 25,120
|
||||
machine_max_feedrate_x = 300,200
|
||||
machine_max_feedrate_y = 300,200
|
||||
machine_max_feedrate_z = 5,12
|
||||
machine_max_jerk_e = 5,2.5
|
||||
machine_max_jerk_x = 10,10
|
||||
machine_max_jerk_y = 10,10
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0.32
|
||||
max_print_height = 300
|
||||
min_layer_height = 0.1
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
remaining_times = 0
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV01\n
|
||||
retract_layer_change = 0
|
||||
retract_length = 2
|
||||
retract_length_toolchange = 10
|
||||
silent_mode = 0
|
||||
start_gcode = G28 ; home all\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; \nG1 X5.1 Y10 Z0.3 F5000.0 ; Move to start position\nG1 X5.1 Y200 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5.4 Y200 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y10 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
use_relative_e_distances = 0
|
||||
printer_model = SV01
|
||||
default_print_profile = 0.20mm SPEED @SV01
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,5 @@
|
||||
[printer:SV01_BLTouch]
|
||||
inherits = SV01
|
||||
end_gcode = G1 X5 Y200 F1000 ; \nM104 S0 ; kill extruder temperature\nM140 S0 ; kill bed temperature\nM107; kill fan\nM84 ; disable motors\nM300; beep\n//M85 S0 ; For use with raspberry.\n
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV02 0.3 nozzle]
|
||||
inherits = SV02
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV02
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV02 0.6 nozzle]
|
||||
inherits = SV02
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV02
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV02 0.8 nozzle]
|
||||
inherits = SV02
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV02
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV03 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,34 @@
|
||||
[printer:SV02]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,280x0,280x240,0x240
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
|
||||
gcode_flavor = marlin2
|
||||
machine_max_acceleration_e = 5000,5000
|
||||
machine_max_acceleration_extruding = 1250,1250
|
||||
machine_max_acceleration_retracting = 1250,1250
|
||||
machine_max_acceleration_x = 1000,960
|
||||
machine_max_acceleration_y = 1000,960
|
||||
machine_max_acceleration_z = 200,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 200,100
|
||||
machine_max_feedrate_y = 200,100
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 4.5,4.5
|
||||
machine_max_jerk_x = 8,8
|
||||
machine_max_jerk_y = 8,8
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV02\n
|
||||
retract_lift_below = 209
|
||||
max_print_height = 300
|
||||
single_extruder_multi_material = 1
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV02
|
||||
default_print_profile = 0.20mm SPEED @SV02
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,5 @@
|
||||
[printer:SV02_BLTouch]
|
||||
inherits = SV02
|
||||
end_gcode = G1 X5 Y200 F1000 ; \nM104 S0 ; kill extruder temperature\nM140 S0 ; kill bed temperature\nM107; kill fan\nM84 ; disable motors\nM300; beep\n//M85 S0 ; For use with raspberry.\n
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV03 0.3 nozzle]
|
||||
inherits = SV03
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV03
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV03 0.6 nozzle]
|
||||
inherits = SV03
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV03
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV03 0.8 nozzle]
|
||||
inherits = SV03
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV03
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,32 @@
|
||||
[printer:SV03]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,350x0,350x350,0x350
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
|
||||
machine_max_acceleration_e = 5000,5000
|
||||
machine_max_acceleration_extruding = 1250,1250
|
||||
machine_max_acceleration_retracting = 1250,1250
|
||||
machine_max_acceleration_x = 1000,960
|
||||
machine_max_acceleration_y = 1000,960
|
||||
machine_max_acceleration_z = 200,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 200,100
|
||||
machine_max_feedrate_y = 200,100
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 4.5,4.5
|
||||
machine_max_jerk_x = 8,8
|
||||
machine_max_jerk_y = 8,8
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV03\n
|
||||
retract_lift_below = 209
|
||||
max_print_height = 400
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV03
|
||||
default_print_profile = 0.20mm SPEED @SV03
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,4 @@
|
||||
[printer:SV03_BLTouch]
|
||||
inherits = SV03
|
||||
end_gcode = G1 X5 Y200 F1000 ; \nM104 S0 ; kill extruder temperature\nM140 S0 ; kill bed temperature\nM107; kill fan\nM84 ; disable motors\nM300; beep\n//M85 S0 ; For use with raspberry.\n
|
||||
start_gcode = //M85 S180 ; For use with raspberry only, it kills the printer if it loses the USB connection and remains inactive for 3 minutes. It works in Marlin 1.1.6\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nG28 ; Home all axes\nG29 ; Auto bed-level (BL-Touch) // Comment if you don't like the automatic level in each print\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0 ; Reset Extruder\nG1 X5 Y20 Z2.0 F3000.0 ; Move to start position\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 X5 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line\nG1 X5 Y200.0 Z0.3 F5000.0 ; Move to side a little\nG1 X5.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z1.0 F3000 ;
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 0.3 nozzle]
|
||||
inherits = SV04
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 0.6 nozzle]
|
||||
inherits = SV04
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
[printer:SV04 0.8 nozzle]
|
||||
inherits = SV04
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 Copy Mode ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Copy Mode 0.3 nozzle]
|
||||
inherits = SV04 Copy Mode
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04 Copy Mode
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Copy Mode 0.6 nozzle]
|
||||
inherits = SV04 Copy Mode
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04 Copy Mode
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV04 Copy Mode 0.8 nozzle]
|
||||
inherits = SV04 Copy Mode
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04 Copy Mode
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 Dual Mode ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Copy Mode]
|
||||
inherits = SV04
|
||||
bed_shape = 0x0,150x0,150x302,0x302
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
printer_variant = 0.4
|
||||
default_print_profile = 0.20mm SPEED @SV04 Copy Mode
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Dual Mode 0.3 nozzle]
|
||||
inherits = SV04 Dual Mode
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04 Dual Mode
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Dual Mode 0.6 nozzle]
|
||||
inherits = SV04 Dual Mode
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04 Dual Mode
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV04 Dual Mode 0.8 nozzle]
|
||||
inherits = SV04 Dual Mode
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04 Dual Mode
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 Mirror Mode ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,50 @@
|
||||
[printer:SV04 Dual Mode]
|
||||
inherits = SV04
|
||||
etruder_offset = 0x0,0x0
|
||||
extruder_colour = #FFFF6F;#FF8040
|
||||
machine_max_acceleration_e = 5000,5000
|
||||
machine_max_acceleration_extruding = 1250,1250
|
||||
machine_max_acceleration_retracting = 1250,1250
|
||||
machine_max_acceleration_x = 1000,960
|
||||
machine_max_acceleration_y = 1000,960
|
||||
machine_max_acceleration_z = 200,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 200,100
|
||||
machine_max_feedrate_y = 200,100
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 4.5,4.5
|
||||
machine_max_jerk_x = 8,8
|
||||
machine_max_jerk_y = 8,8
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0.25,0.25
|
||||
max_print_height = 402
|
||||
min_layer_height = 0.07,0.07
|
||||
nozzle_diameter = 0.4,0.4
|
||||
parking_pos_retraction = 92
|
||||
pause_print_gcode = M601
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV04\n
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2,2
|
||||
retract_before_wipe = 0%,0%
|
||||
retract_layer_change = 1,1
|
||||
retract_length = 0.5,0.5
|
||||
retract_length_toolchange = 4,4
|
||||
retract_lift = 0,0
|
||||
retract_lift_above = 0,0
|
||||
retract_lift_below = 209,209
|
||||
retract_restart_extra = 0,0
|
||||
retract_restart_extra_toolchange = 0,0
|
||||
retract_speed = 40,40
|
||||
silent_mode = 0
|
||||
single_extruder_multi_material = 0
|
||||
deretract_speed = 0,0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
printer_variant = 0.4
|
||||
default_print_profile = 0.20mm SPEED @SV04 Dual Mode
|
||||
default_filament_profile = Generic PLA @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Mirror Mode 0.3 nozzle]
|
||||
inherits = SV04 Mirror Mode
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04 Mirror Mode
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Mirror Mode 0.6 nozzle]
|
||||
inherits = SV04 Mirror Mode
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04 Mirror Mode
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV04 Mirror Mode 0.8 nozzle]
|
||||
inherits = SV04 Mirror Mode
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04 Mirror Mode
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 Single Mode 01 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,12 @@
|
||||
[printer:SV04 Mirror Mode]
|
||||
inherits = SV04
|
||||
bed_shape = 0x0,115x0,115x302,0x302
|
||||
deretract_speed = 0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
printer_variant = 0.4
|
||||
default_print_profile = 0.20mm SPEED @SV04 Mirror Mode
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 01 0.3 nozzle]
|
||||
inherits = SV04 Single Mode 01
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04 Single Mode 01
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 01 0.6 nozzle]
|
||||
inherits = SV04 Single Mode 01
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04 Single Mode 01
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV04 Single Mode 01 0.8 nozzle]
|
||||
inherits = SV04 Single Mode 01
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04 Single Mode 01
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV04 Single Mode 02 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 01]
|
||||
inherits = SV04
|
||||
deretract_speed = 0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
start_gcode = M104 T0 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 T0 S[first_layer_temperature] ; wait for extruder temp\nG28;\nM420 S1;\nT0;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
printer_variant = 0.4
|
||||
default_print_profile = 0.20mm SPEED @SV04 Single Mode 01
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 02 0.3 nozzle]
|
||||
inherits = SV04 Single Mode 02
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV04 Single Mode 02
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 02 0.6 nozzle]
|
||||
inherits = SV04 Single Mode 02
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV04 Single Mode 02
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV04 Single Mode 02 0.8 nozzle]
|
||||
inherits = SV04 Single Mode 02
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
; start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV04 Single Mode 02
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV05 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV04 Single Mode 02]
|
||||
inherits = SV04
|
||||
deretract_speed = 0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
start_gcode = M104 T1 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 T1 S[first_layer_temperature] ; wait for extruder temp\nG28;\nM420 S1;\nT1;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
printer_variant = 0.4
|
||||
default_print_profile = 0.20mm SPEED @SV04 Single Mode 02
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,51 @@
|
||||
[printer:SV04]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,302x0,302x302,0x302
|
||||
deretract_speed = 0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
extra_loading_move = -2
|
||||
extruder_colour = ;
|
||||
extruder_offset = 0x0
|
||||
machine_max_acceleration_e = 5000
|
||||
machine_max_acceleration_extruding = 1250
|
||||
machine_max_acceleration_retracting = 1250
|
||||
machine_max_acceleration_x = 1000
|
||||
machine_max_acceleration_y = 1000
|
||||
machine_max_acceleration_z = 200
|
||||
machine_max_feedrate_e = 120
|
||||
machine_max_feedrate_x = 200
|
||||
machine_max_feedrate_y = 200
|
||||
machine_max_feedrate_z = 12
|
||||
machine_max_jerk_e = 4.5
|
||||
machine_max_jerk_x = 8
|
||||
machine_max_jerk_y = 8
|
||||
machine_max_jerk_z = 0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
max_layer_height = 0.25
|
||||
max_print_height = 402
|
||||
min_layer_height = 0.07
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
pause_print_gcode = M601
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV04\n
|
||||
remaining_times = 1
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 0%
|
||||
retract_layer_change = 1
|
||||
retract_length = 0.5
|
||||
retract_length_toolchange = 4
|
||||
retract_lift = 0
|
||||
retract_lift_above = 0
|
||||
retract_lift_below = 209
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 40
|
||||
silent_mode = 0
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV04
|
||||
default_print_profile = 0.20mm SPEED @SV04
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
thumbnails = 160x120
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV05 0.3 nozzle]
|
||||
inherits = SV05
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV05
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV05 0.6 nozzle]
|
||||
inherits = SV05
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV05
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV05 0.8 nozzle]
|
||||
inherits = SV05
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.25
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV05
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV06 ---XXX
|
||||
# XXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,31 @@
|
||||
[printer:SV05]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,220x0,220x220,0x220
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
machine_max_acceleration_e = 5000,5000
|
||||
machine_max_acceleration_extruding = 1250,1250
|
||||
machine_max_acceleration_retracting = 1250,1250
|
||||
machine_max_acceleration_x = 1000,960
|
||||
machine_max_acceleration_y = 1000,960
|
||||
machine_max_acceleration_z = 200,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 200,100
|
||||
machine_max_feedrate_y = 200,100
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 4.5,4.5
|
||||
machine_max_jerk_x = 8,8
|
||||
machine_max_jerk_y = 8,8
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV05\n
|
||||
retract_lift_below = 209
|
||||
max_print_height = 300
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV05
|
||||
default_print_profile = 0.20mm SPEED @SV05
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV06 0.3 nozzle]
|
||||
inherits = SV06
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV06
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV06 0.6 nozzle]
|
||||
inherits = SV06
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
deretract_speed = 28
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV06
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV06 0.8 nozzle]
|
||||
inherits = SV06
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.3
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV06
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV06 PLUS ---XXX
|
||||
# XXXXXXXXXXXXXXXXXXXXXXX
|
||||
|
||||
@@ -0,0 +1,11 @@
|
||||
[printer:SV06 PLUS 0.3 nozzle]
|
||||
inherits = SV06 PLUS
|
||||
nozzle_diameter = 0.3
|
||||
max_layer_height = 0.15
|
||||
min_layer_height = 0.05
|
||||
printer_variant = 0.3
|
||||
retract_lift = 0.15
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.10mm DETAIL @0.3 nozzle SV06
|
||||
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,13 @@
|
||||
[printer:SV06 PLUS 0.6 nozzle]
|
||||
inherits = SV06 PLUS
|
||||
nozzle_diameter = 0.6
|
||||
max_layer_height = 0.40
|
||||
min_layer_height = 0.15
|
||||
printer_variant = 0.6
|
||||
retract_length = 0.5
|
||||
retract_speed = 30
|
||||
deretract_speed = 30
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.30mm QUALITY @0.6 nozzle SV06
|
||||
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
[printer:SV06 PLUS 0.8 nozzle]
|
||||
inherits = SV06 PLUS
|
||||
nozzle_diameter = 0.8
|
||||
max_layer_height = 0.6
|
||||
min_layer_height = 0.2
|
||||
printer_variant = 0.8
|
||||
retract_length = 0.7
|
||||
retract_speed = 40
|
||||
deretract_speed = 23
|
||||
retract_lift = 0.3
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
default_print_profile = 0.40mm QUALITY @0.8 nozzle SV06
|
||||
default_filament_profile = Generic PLA 0.8 @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
|
||||
|
||||
# XXXXXXXXXXXXXXXXXXXXX
|
||||
# XXX--- BLTOUCH ---XXX
|
||||
# XXXXXXXXXXXXXXXXXXXXX
|
||||
|
||||
|
||||
@@ -0,0 +1,36 @@
|
||||
[printer:SV06 PLUS]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,300x0,300x300,0x300
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
machine_max_acceleration_e = 5000
|
||||
machine_max_acceleration_extruding = 1250
|
||||
machine_max_acceleration_retracting = 1250
|
||||
machine_max_acceleration_x = 1000
|
||||
machine_max_acceleration_y = 1000
|
||||
machine_max_acceleration_z = 200
|
||||
machine_max_feedrate_e = 120
|
||||
machine_max_feedrate_x = 200
|
||||
machine_max_feedrate_y = 200
|
||||
machine_max_feedrate_z = 12
|
||||
machine_max_jerk_e = 4.5
|
||||
machine_max_jerk_x = 8
|
||||
machine_max_jerk_y = 8
|
||||
machine_max_jerk_z = 0.4
|
||||
machine_min_extruding_rate = 0
|
||||
machine_min_travel_rate = 0
|
||||
retract_before_travel = 0.5
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
retract_length = 0.5
|
||||
retract_speed = 30
|
||||
deretract_speed = 30
|
||||
retract_lift = 0
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV06 PLUS\n
|
||||
retract_lift_below = 209
|
||||
max_print_height = 340
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV06 PLUS
|
||||
default_print_profile = 0.20mm SPEED @SV06
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,31 @@
|
||||
[printer:SV06]
|
||||
inherits = *common*
|
||||
bed_shape = 0x0,220x0,220x220,0x220
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
machine_max_acceleration_e = 5000,5000
|
||||
machine_max_acceleration_extruding = 1250,1250
|
||||
machine_max_acceleration_retracting = 1250,1250
|
||||
machine_max_acceleration_x = 1000,960
|
||||
machine_max_acceleration_y = 1000,960
|
||||
machine_max_acceleration_z = 200,200
|
||||
machine_max_feedrate_e = 120,120
|
||||
machine_max_feedrate_x = 200,100
|
||||
machine_max_feedrate_y = 200,100
|
||||
machine_max_feedrate_z = 12,12
|
||||
machine_max_jerk_e = 4.5,4.5
|
||||
machine_max_jerk_x = 8,8
|
||||
machine_max_jerk_y = 8,8
|
||||
machine_max_jerk_z = 0.4,0.4
|
||||
machine_min_extruding_rate = 0,0
|
||||
machine_min_travel_rate = 0,0
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV06\n
|
||||
retract_lift_below = 209
|
||||
max_print_height = 250
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
printer_model = SV06
|
||||
default_print_profile = 0.20mm SPEED @SV06
|
||||
thumbnails = 160x120
|
||||
|
||||
|
||||
@@ -0,0 +1,68 @@
|
||||
[printer:*common*]
|
||||
printer_technology = FFF
|
||||
bed_shape = 0x0,220x0,220x220,0x220
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
|
||||
between_objects_gcode =
|
||||
deretract_speed = 0
|
||||
end_gcode = G91 ;Relative positioning\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positioning\nG1 X10 Y220 ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = marlin
|
||||
silent_mode = 0
|
||||
remaining_times = 1
|
||||
machine_max_acceleration_e = 10000
|
||||
machine_max_acceleration_extruding = 2000
|
||||
machine_max_acceleration_retracting = 1500
|
||||
machine_max_acceleration_x = 9000
|
||||
machine_max_acceleration_y = 9000
|
||||
machine_max_acceleration_z = 500
|
||||
machine_max_feedrate_e = 120
|
||||
machine_max_feedrate_x = 500
|
||||
machine_max_feedrate_y = 500
|
||||
machine_max_feedrate_z = 12
|
||||
machine_max_jerk_e = 2.5
|
||||
machine_max_jerk_x = 10
|
||||
machine_max_jerk_y = 10
|
||||
machine_max_jerk_z = 0.2
|
||||
machine_min_extruding_rate = 0
|
||||
machine_min_travel_rate = 0
|
||||
machine_limits_usage = time_estimate_only
|
||||
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
|
||||
max_layer_height = 0.25
|
||||
min_layer_height = 0.07
|
||||
max_print_height = 250
|
||||
nozzle_diameter = 0.4
|
||||
octoprint_apikey =
|
||||
octoprint_host =
|
||||
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_SOVOL\nPRINTER_MODEL_SV06\n
|
||||
printer_settings_id =
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 0%
|
||||
retract_layer_change = 1
|
||||
retract_length = 0.5
|
||||
retract_length_toolchange = 4
|
||||
retract_lift = 0
|
||||
retract_lift_above = 0
|
||||
retract_lift_below = 0
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 40
|
||||
serial_port =
|
||||
serial_speed = 250000
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28;\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position\nG1 X5.1 Y30.0 Z0.28 F1500.0 E1 ;Draw a short bit in case the extruder turns in the wrong direction\nG1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up
|
||||
toolchange_gcode =
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 1
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 1
|
||||
z_offset = 0
|
||||
printer_model =
|
||||
printer_variant = 0.4
|
||||
extruder_clearance_height = 20
|
||||
extruder_clearance_radius = 45
|
||||
default_print_profile = 0.20mm QUALITY
|
||||
default_filament_profile = Generic PLA @SOVOL
|
||||
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
|
||||
|
||||
|
||||
@@ -0,0 +1,25 @@
|
||||
[printer:*multimaterial*]
|
||||
inherits = *common*
|
||||
deretract_speed = 50
|
||||
retract_before_travel = 3
|
||||
retract_before_wipe = 60%
|
||||
retract_layer_change = 0
|
||||
retract_length = 4
|
||||
retract_lift = 0.6
|
||||
retract_lift_above = 0
|
||||
retract_lift_below = 199
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 80
|
||||
parking_pos_retraction = 92
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
single_extruder_multi_material = 1
|
||||
variable_layer_height = 1
|
||||
printer_model = SV02
|
||||
|
||||
|
||||
# XXXXXXXXXXXXXXXXXX
|
||||
# XXX--- SV01 ---XXX
|
||||
# XXXXXXXXXXXXXXXXXX
|
||||
|
||||
Reference in New Issue
Block a user