Initial Profile Sources

profile_sources/non-prusa-fff/gCreate/print/0.10mm - Very Thin Layers @GCREATE.ini

@@ -0,0 +1,6 @@
+[print:0.10mm - Very Thin Layers @GCREATE]
+inherits = *0.10mm*
+#Below works. Will only allow gMax 2 and gMax 2 Pro with specific nozzle sizes
+#compatible_printers_condition = nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5 and printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2.*/
+compatible_printers_condition = (nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.15mm - Thin Layers @GCREATE.ini

@@ -0,0 +1,6 @@
+[print:0.15mm - Thin Layers @GCREATE]
+inherits = *0.15mm*
+#Below works. Will only allow gMax 2 and gMax 2 Pro with specific nozzle sizes
+#compatible_printers_condition = nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5 and printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2.*/
+compatible_printers_condition = (nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Dual 2in1 @GCREATE.ini

@@ -0,0 +1,11 @@
+[print:0.20mm - Dual 2in1 @GCREATE]
+inherits = *0.20mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2DUAL2IN1/)
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 1
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 75
+wipe_tower_x = 100
+wipe_tower_y = 300
+

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Dual 2in1 PLA with PVA Support @GCREATE.ini

@@ -0,0 +1,151 @@
+[print:0.20mm - Dual 2in1 PLA with PVA Support @GCREATE]
+inherits = *0.20mm*; 0.20mm - Dual 2in1 @GCREATE
+compatible_printers_condition = (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0
+bridge_acceleration = 0
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+complete_objects = 0
+default_acceleration = 400
+dont_support_bridges = 0
+draft_shield = 0
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 75%
+external_perimeters_first = 0
+extra_perimeters = 1
+extrusion_width = 0
+fill_angle = 45
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.23
+first_layer_speed = 35
+gap_fill_speed = 30
+gcode_comments = 0
+gcode_label_objects = 1
+infill_acceleration = 0
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 80
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 15
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 65
+perimeters = 4
+post_process = 
+print_settings_id = 0.20mm - Dual 2in1 @GCREATE PLA PVA Support
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+single_extruder_multi_material_priming = 0
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 30
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 35
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 1
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 0
+support_material_contact_distance = 0
+support_material_enforce_layers = 0
+support_material_extruder = 2
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 2
+support_material_interface_layers = 4
+support_material_interface_spacing = 0
+support_material_interface_speed = 90%
+support_material_pattern = rectilinear-grid
+support_material_spacing = 3
+support_material_speed = 65
+support_material_synchronize_layers = 1
+support_material_threshold = 0
+support_material_with_sheath = 1
+support_material_xy_spacing = 0
+thin_walls = 1
+threads = 8
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 35
+top_solid_layers = 4
+top_solid_min_thickness = 0
+travel_speed = 130
+wipe_tower = 1
+wipe_tower_bridging = 20
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 75
+wipe_tower_x = 50
+wipe_tower_y = 400
+
+
+
+##################################
+#  SET FILAMENT VARIANTS         #
+##################################
+
+# TEMPLATE
+
+#[filament:*PLA*]
+#inherits = *common*
+
+#filament_type = PLA
+#filament_density = 1.24
+#filament_cost = 20
+
+#first_layer_bed_temperature = 60
+#first_layer_temperature = 200
+#temperature = 200
+#bed_temperature = 60
+
+#fan_always_on = 1
+#cooling = 1
+#disable_fan_first_layers = 1
+#max_fan_speed = 90
+#min_fan_speed = 90
+#bridge_fan_speed = 75
+
+#fan_below_layer_time = 15
+#slowdown_below_layer_time = 10
+
+#compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
+
+
+# Common filament preset across all filaments

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Dual Chimera @GCREATE.ini

@@ -0,0 +1,15 @@
+[print:0.20mm - Dual Chimera @GCREATE]
+inherits = *0.20mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2DUAL/) 
+# wipe tower
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 1
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 75
+wipe_tower_x = 100
+wipe_tower_y = 300
+# ooze prevention
+ooze_prevention = 1
+standby_temperature_delta = -15
+

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Standard Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.20mm - Standard Layers @GCREATE]
+inherits = *0.20mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Standard Layers Fast @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.20mm - Standard Layers Fast @GCREATE]
+inherits = *0.20mm*; *FAST*
+compatible_printers_condition = (nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.20mm - Standard Layers Slow (PETG and TPU) @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.20mm - Standard Layers Slow (PETG and TPU) @GCREATE]
+inherits = *0.20mm*; *SLOW*
+compatible_printers_condition = (nozzle_diameter[0]==0.3 or nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.25mm - Thick Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.25mm - Thick Layers @GCREATE]
+inherits = *0.25mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.30mm - Very Thick Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.30mm - Very Thick Layers @GCREATE]
+inherits = *0.3mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.4 or nozzle_diameter[0]==0.5) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.40mm - High Output Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.40mm - High Output Layers @GCREATE]
+inherits = *0.4mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.5 or nozzle_diameter[0]==0.8 or nozzle_diameter[0]==1.0) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.50mm - High Output Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.50mm - High Output Layers @GCREATE]
+inherits = *0.5mm*
+compatible_printers_condition = (nozzle_diameter[0]==0.8 or nozzle_diameter[0]==1.0) and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/0.60mm - High Output Layers @GCREATE.ini

@@ -0,0 +1,4 @@
+[print:0.60mm - High Output Layers @GCREATE]
+inherits = *0.6mm*
+compatible_printers_condition = nozzle_diameter[0]==0.8 or nozzle_diameter[0]==1.0 and (printer_model=~/.*GMAX2PRO.*/ or printer_model=~/.*GMAX2/ or printer_model=~/.*GMAX15P.*/) and ! (printer_model=~/.*GMAX2DUAL2IN1.*/ or printer_model=~/.*GMAX2DUAL.*/)
+

profile_sources/non-prusa-fff/gCreate/print/_0.10mm_.ini

@@ -0,0 +1,8 @@
+[print:*0.10mm*]
+inherits = *common*
+layer_height = 0.10
+first_layer_height = 150%
+perimeters = 3
+bottom_solid_layers = 6
+top_solid_layers = 8
+

profile_sources/non-prusa-fff/gCreate/print/_0.15mm_.ini

@@ -0,0 +1,8 @@
+[print:*0.15mm*]
+inherits = *common*
+layer_height = 0.15
+first_layer_height = 125%
+perimeters = 3
+bottom_solid_layers = 5
+top_solid_layers = 6
+

profile_sources/non-prusa-fff/gCreate/print/_0.20mm_.ini

@@ -0,0 +1,10 @@
+[print:*0.20mm*]
+inherits = *common*
+layer_height = 0.2
+first_layer_height = 125%
+first_layer_speed = 50%
+perimeters = 3
+bottom_solid_layers = 3
+top_solid_layers = 4
+
+

profile_sources/non-prusa-fff/gCreate/print/_0.25mm_.ini

@@ -0,0 +1,9 @@
+[print:*0.25mm*]
+inherits = *common*
+layer_height = 0.25
+first_layer_height = 100%
+first_layer_speed = 50%
+top_infill_extrusion_width = 0
+bottom_solid_layers = 3
+top_solid_layers = 4
+

profile_sources/non-prusa-fff/gCreate/print/_0.3mm_.ini

@@ -0,0 +1,9 @@
+[print:*0.3mm*]
+inherits = *common*
+layer_height = 0.3
+first_layer_height = 100%
+first_layer_speed = 50%
+top_infill_extrusion_width = 0
+bottom_solid_layers = 3
+top_solid_layers = 4
+

profile_sources/non-prusa-fff/gCreate/print/_0.4mm_.ini

@@ -0,0 +1,10 @@
+[print:*0.4mm*]
+inherits = *common*
+layer_height = 0.4
+first_layer_height = 100%
+first_layer_speed = 50%
+top_infill_extrusion_width = 0
+bottom_solid_layers = 3
+top_solid_layers = 4
+
+

profile_sources/non-prusa-fff/gCreate/print/_0.5mm_.ini

@@ -0,0 +1,9 @@
+[print:*0.5mm*]
+inherits = *common*
+layer_height = 0.5
+first_layer_height = 100%
+first_layer_speed = 45%
+top_infill_extrusion_width = 0
+bottom_solid_layers = 3
+top_solid_layers = 3
+

profile_sources/non-prusa-fff/gCreate/print/_0.6mm_.ini

@@ -0,0 +1,9 @@
+[print:*0.6mm*]
+inherits = *common*
+layer_height = 0.6
+first_layer_height = 100%
+first_layer_speed = 40%
+top_infill_extrusion_width = 0
+bottom_solid_layers = 3
+top_solid_layers = 3
+

profile_sources/non-prusa-fff/gCreate/print/_FAST_.ini

@@ -0,0 +1,41 @@
+[print:*FAST*]
+#SPEED
+perimeter_speed = 70
+small_perimeter_speed = 85%
+external_perimeter_speed = 75%
+infill_speed = 85%
+solid_infill_speed = 70%
+top_solid_infill_speed = 65%
+support_material_speed = 75%
+bridge_speed = 45
+gap_fill_speed = 30
+
+
+#############################################################################
+#  SET PRINTER AND NOZZLE SPECIFIC PROFLIES (THESE SHOW INT HE DROPDOWN)    #
+#############################################################################
+
+#we can add specific changes for specific printers and nozzle sizes. Just put in conditionals
+# compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ and printer_model=~/.*GMAX2PRO.*/ and nozzle_diameter[0]==0.5
+
+
+#TEMPLATE
+
+#SPEED SETTINGS
+#[print:0.10mm - Very Thin Layers @GCREATE]
+#perimeter_speed = 100%
+#small_perimeter_speed = 100%
+#external_perimeter_speed = 100%
+#infill_speed = 100%
+#solid_infill_speed = 100%
+#top_solid_infill_speed = 100%
+#support_material_speed = 100%
+#bridge_speed = 100%
+#don't adjust gap speed above 30 or it causes layer shifting
+#gap_fill_speed = 30
+
+#ADVANCED
+#
+
+
+

profile_sources/non-prusa-fff/gCreate/print/_SLOW_.ini

@@ -0,0 +1,12 @@
+[print:*SLOW*]
+#SPEED
+perimeter_speed = 40
+small_perimeter_speed = 35
+external_perimeter_speed = 35
+infill_speed = 40
+solid_infill_speed = 40
+top_solid_infill_speed = 30
+support_material_speed = 35
+bridge_speed = 35
+gap_fill_speed = 30
+

profile_sources/non-prusa-fff/gCreate/print/_common_.ini

@@ -0,0 +1,103 @@
+[print:*common*]
+avoid_crossing_perimeters = 0
+bridge_angle = 0
+bridge_flow_ratio = 0.95
+bridge_speed = 35
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+complete_objects = 0
+default_acceleration = 400
+dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
+external_fill_pattern = rectilinear
+external_perimeters_first = 0
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 65%
+extra_perimeters = 0
+extrusion_width = 0
+fill_angle = 45
+fill_density = 20%
+fill_pattern = 3dhoneycomb
+first_layer_extrusion_width = 0
+first_layer_height = 125%
+first_layer_speed = 65%
+gap_fill_speed = 30
+gcode_comments = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 50
+interface_shells = 0
+max_print_speed = 100
+max_volumetric_extrusion_rate_slope_negative = 0
+max_volumetric_extrusion_rate_slope_positive = 0
+max_volumetric_speed = 0
+min_skirt_length = 15
+notes = 
+overhangs = 0
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}.gcode
+perimeters = 2
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+post_process = 
+print_settings_id = 
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirts = 1
+skirt_distance = 2
+skirt_height = 1
+small_perimeter_speed = 50%
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 80%
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0
+support_material_interface_extruder = 0
+support_material_angle = 0
+support_material_buildplate_only = 0
+support_material_enforce_layers = 0
+support_material_contact_distance = 0.2
+support_material_interface_contact_loops = 0
+support_material_interface_layers = 4
+support_material_interface_spacing = 0.2
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 40
+support_material_synchronize_layers = 0
+support_material_threshold = 45
+support_material_with_sheath = 0
+support_material_xy_spacing = 60%
+thin_walls = 0
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50%
+travel_speed = 100
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 75
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0
+
+##################################
+#  SET LAYER HEIGHT VARIANTS     #
+##################################
+
+#common layer height variants
+