[filament:Generic TPU @Papapiu]
inherits = Generic PLA @Papapiu
bed_temperature = 30
bridge_fan_speed = 100
bridge_internal_fan_speed = -1
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 2
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.89
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF00FF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 20
filament_custom_variables = ""
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 5
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "This is a profile for TPU95A. It was tested with Anycubic TPU95A, but most of the economy TPU filaments behave pretty similar.\n\nYou will want to optimize the temperature. Even different colors of the same brand can require 10° more or less.\n\nIf you experience clogs or grinding, reduce the maximum volumetric speed!"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 1
filament_retract_lift = 0.1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = nil
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 30
first_layer_temperature = 220
full_fan_speed_layer = 4
max_fan_speed = 100
max_speed_reduction = 95%
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 8
start_filament_gcode = ""
temperature = 220
top_fan_speed = -1