mirror of
https://github.com/Santoku-Slicer/Profiles.git
synced 2026-07-07 16:59:47 +00:00
Dark98
86 lines
2.5 KiB
INI
86 lines
2.5 KiB
INI
[filament:*common*]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
disable_rapid_cooling_fan_first_layers = 3
|
|
enable_advance_pressure = 1
|
|
enable_auxiliary_fan = 100
|
|
enable_auxiliary_fan_unseal = 0
|
|
enable_dynamic_fan_speeds = 0
|
|
enable_volume_fan = 100
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 60
|
|
filament_colour = #3399FF
|
|
filament_cooling_final_speed = 0
|
|
filament_cooling_initial_speed = 0
|
|
filament_cooling_moves = 0
|
|
filament_cost = 0
|
|
filament_density = 1.24
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 0
|
|
filament_loading_speed_start = 0
|
|
filament_max_volumetric_speed = 20
|
|
filament_minimal_purge_on_wipe_tower = 5
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id =
|
|
filament_shrink = 100
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 0
|
|
filament_toolchange_delay = 0
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 0
|
|
filament_unloading_speed_start = 0
|
|
filament_vendor = QIDI
|
|
filament_wipe = nil
|
|
filament_wipe_distance = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 210
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = 100
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 20
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
seal_print = 1
|
|
slowdown_below_layer_time = 8
|
|
start_filament_gcode = "; Filament gcode\nM900 K0.02 T0.03\n"
|
|
temperature = 220
|
|
chamber_temperature = 0
|
|
cooling_slowdown_logic = consistent_surface
|
|
cooling_perimeter_transition_distance = 3
|
|
|
|
# QIDI filament preset
|