mirror of
https://github.com/Santoku-Slicer/Profiles.git
synced 2026-07-07 16:59:47 +00:00
Dark98
30 lines
2.3 KiB
INI
30 lines
2.3 KiB
INI
[printer:*dualextruder*]
|
|
single_extruder_multi_material = 1
|
|
cooling_tube_length = 23
|
|
cooling_tube_retraction = 35
|
|
extra_loading_move = -2
|
|
parking_pos_retraction = 80
|
|
deretract_speed = 40,40
|
|
extruder_colour = #0080C0;#FFFF9F
|
|
extruder_offset = 0x0,0x0
|
|
max_layer_height = 0.28,0.28
|
|
min_layer_height = 0.08,0.08
|
|
nozzle_diameter = 0.4,0.4
|
|
retract_before_travel = 2,2
|
|
retract_before_wipe = 70%,70%
|
|
retract_layer_change = 1,1
|
|
retract_length = 5,5
|
|
retract_length_toolchange = 1,1
|
|
retract_lift = 0,0
|
|
retract_lift_above = 0,0
|
|
retract_lift_below = 0,0
|
|
retract_restart_extra = 0,0
|
|
retract_restart_extra_toolchange = 0,0
|
|
retract_speed = 60,60
|
|
wipe = 1,1
|
|
start_gcode = T[initial_tool] ; set active extruder\nM413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S{first_layer_bed_temperature[0]} ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; auto bed levelling - remove ; at beginning of line to enable\n;M420 S1 ; enable mesh - remove ; at beginning of line to enable\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG1 Z0.28 F240 ; move down to prime nozzle\nG92 E0 ; reset extruder\nG1 E90 ; load filament\nG92 E0 ; reset extruder\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000 ; move over for second prime line\nG92 E0 ; reset extruder\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0 ; reset extruder
|
|
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\nG1 E-80 F2000 ; unload filament\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
|
|
|
|
# Copy of Creality CR-X config for the Neptune 2D (dual extruder, single hotend)
|
|
|