Profiles/repos/orcaslicer-fff/OrcaFilamentLibrary/02.03.02.60.ini

[vendor]
repo_id = orcaslicer-fff
name = OrcaFilamentLibrary
config_version = 02.03.02.60
description = Orca Filament Library
force_update = 0

[filament:fdm_filament_common]
from = system
instantiation = false
activate_air_filtration = 0
chamber_temperatures = 0
close_fan_the_first_x_layers = 3
complete_print_exhaust_fan_speed = 70
cool_plate_temp = 60
cool_plate_temp_initial_layer = 60
during_print_exhaust_fan_speed = 70
eng_plate_temp = 60
eng_plate_temp_initial_layer = 60
fan_cooling_layer_time = 60
fan_max_speed = 100
fan_min_speed = 35
filament_cost = 0
filament_density = 0
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_flow_ratio = 1
filament_is_support = 0
filament_long_retractions_when_cut = nil
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 15
filament_retract_before_wipe = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = nil
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
filament_vendor = Generic
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
filament_scarf_seam_type = none
filament_scarf_height = 10%
filament_scarf_gap = 0%
filament_scarf_length = 10
filament_shrink = 100%
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
nozzle_temperature = 200
nozzle_temperature_initial_layer = 200
overhang_fan_speed = 100
overhang_fan_threshold = 95%
reduce_fan_stop_start_freq = 0
required_nozzle_HRC = 3
supertack_plate_temp = 45
supertack_plate_temp_initial_layer = 45
slow_down_for_layer_cooling = 1
slow_down_layer_time = 8
slow_down_min_speed = 10
temperature_vitrification = 100
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60
filament_start_gcode = ; Filament gcode

filament_end_gcode = ; filament end gcode

compatible_printers =

[filament:FusRock ABS-GF @base]
inherits = fdm_filament_common
from = system
filament_id = OGFR00
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）.
filament_extruder_variant = Direct Drive Standard
filament_adhesiveness_category = 200
filament_type = ABS-GF
filament_vendor = FusRock
filament_flow_ratio = 0.92
filament_density = 1.08
filament_cost = 13
nozzle_temperature_range_low = 240
nozzle_temperature_range_high = 280
cool_plate_temp_initial_layer = 0
cool_plate_temp = 0
supertack_plate_temp_initial_layer = 0
supertack_plate_temp = 0
eng_plate_temp_initial_layer = 105
eng_plate_temp = 105
hot_plate_temp_initial_layer = 105
hot_plate_temp = 105
textured_plate_temp_initial_layer = 105
textured_plate_temp = 105
nozzle_temperature_initial_layer = 260
nozzle_temperature = 270
filament_max_volumetric_speed = 18
close_fan_the_first_x_layers = 3
fan_min_speed = 10
fan_cooling_layer_time = 12
fan_max_speed = 30
slow_down_layer_time = 4
reduce_fan_stop_start_freq = 0
slow_down_for_layer_cooling = 1
slow_down_min_speed = 20
enable_overhang_bridge_fan = 1
overhang_fan_threshold = 10%
overhang_threshold_participating_cooling = 100%
overhang_fan_speed = 30
pre_start_fan_time = 0
additional_cooling_fan_speed = 0
activate_air_filtration = 1
during_print_exhaust_fan_speed = 30
complete_print_exhaust_fan_speed = 10
filament_retraction_length = 0.8
filament_z_hop = 0.4
filament_z_hop_types = Spiral Lift
filament_retraction_speed = 30
filament_deretraction_speed = 0
filament_retraction_minimum_travel = 2
filament_retract_when_changing_layer = 0
filament_wipe = 0
filament_wipe_distance = 2
filament_retract_before_wipe = 100%
filament_end_gcode = ; filament end gcode 


filament_notes = //EN
1.Be sure to read it carefully before using (https://wiki.fusrock.com).
2.When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）.\n3.Thank you for choosing us FusRock.
*This setting may not be able to adapt to all models. In some cases, you need to modify and adjust the parameters by yourself to improve the printing effect.
*FusRock 3D printing filaments are intended for general-purpose printing and have been tested under standard conditions. However, the performance and safety of printed objects are affected by multiple factors, including printing parameters, model design, usage environment, and the specific application.
*By using FusRock materials, the user acknowledges and agrees to independently evaluate whether the printed parts are suitable for their intended use, and assumes all associated risks.
*FusRock shall not be held liable for any damage, injury, or loss that may result from the use of printed products made with our materials, including but not limited to structural failure, functional defects, or safety hazards under actual usage conditions.Before applying printed parts in any critical, functional, or commercial context, thorough testing must be conducted. Except for the certifications explicitly stated for specific FusRock materials, our products are not certified for medical, aerospace, or life-support applications.
//CN
1.使用前请务必仔细阅读（https://wiki.fusrock.com）。
2.打印该耗材时，可能会出现喷嘴堵塞、拉丝、翘边以及层间附着力不足等问题。为了获得更好的打印效果，请参考此维基页面：高温 / 工程材料打印技巧（https://wiki.fusrock.com）。
3.感谢您选择FusRock。
*此设置不一定能够适配所有模型，存在部分情况下需要您自行修改调整参数来提升打印效果。
*FusRock 3D打印耗材适用于通用打印用途，已在标准条件下进行测试。然而，打印成品的性能与安全性受多种因素影响，包括打印参数、模型设计、使用环境及实际用途。
*使用FusRock材料即表示用户已知悉并同意，自行评估打印件是否适用于其具体应用，并承担由此产生的全部风险。
*FusRock对使用本公司耗材打印的产品在实际应用中可能导致的任何损害、伤害或损失不承担任何责任，包括但不限于结构失效、功能异常或使用环境中的安全隐患。在将打印件应用于关键、功能性或商业性场景前，请务必进行充分测试。除FusRock已标明材料所获得的各项认证资质外，FusRock产品未取得医疗、航天或生命支持系统认证资质。
impact_strength_z = 5.3

[filament:fdm_filament_abs]
inherits = fdm_filament_common
from = system
instantiation = false
activate_air_filtration = 0
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 100
eng_plate_temp_initial_layer = 105
fan_cooling_layer_time = 30
fan_max_speed = 80
fan_min_speed = 10
filament_cost = 20
filament_density = 1.04
filament_max_volumetric_speed = 12
filament_type = ABS
hot_plate_temp = 100
hot_plate_temp_initial_layer = 105
nozzle_temperature = 260
nozzle_temperature_initial_layer = 260
nozzle_temperature_range_high = 280
nozzle_temperature_range_low = 240
overhang_fan_speed = 80
overhang_fan_threshold = 25%
reduce_fan_stop_start_freq = 1
slow_down_layer_time = 3
slow_down_min_speed = 10
textured_plate_temp = 100
textured_plate_temp_initial_layer = 105
filament_flow_ratio = 0.926
temperature_vitrification = 110

[filament:fdm_filament_asa]
inherits = fdm_filament_common
from = system
instantiation = false
activate_air_filtration = 0
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 100
eng_plate_temp_initial_layer = 105
fan_cooling_layer_time = 35
fan_max_speed = 80
fan_min_speed = 10
filament_cost = 20
filament_density = 1.04
filament_max_volumetric_speed = 12
filament_type = ASA
hot_plate_temp = 100
hot_plate_temp_initial_layer = 105
nozzle_temperature = 260
nozzle_temperature_initial_layer = 260
nozzle_temperature_range_high = 280
nozzle_temperature_range_low = 240
overhang_fan_speed = 80
overhang_fan_threshold = 25%
reduce_fan_stop_start_freq = 1
slow_down_layer_time = 3
slow_down_min_speed = 10
textured_plate_temp = 100
textured_plate_temp_initial_layer = 105
filament_flow_ratio = 0.926
temperature_vitrification = 110

[filament:fdm_filament_bvoh]
inherits = fdm_filament_common
from = system
filament_id = OGFS97
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 40
cool_plate_temp_initial_layer = 40
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 69.99
filament_density = 1.13
filament_is_support = 1
filament_max_volumetric_speed = 8
filament_type = BVOH
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
slow_down_min_speed = 10
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:fdm_filament_cope]
inherits = fdm_filament_common
from = system
filament_id = OGFLC99
instantiation = false
filament_type = CoPE
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 20
filament_density = 1.29
filament_max_volumetric_speed = 16
filament_scarf_seam_type = none
filament_scarf_gap = 15%
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55
filament_flow_ratio = 0.98

[filament:fdm_filament_eva]
inherits = fdm_filament_common
from = system
filament_id = OGFR99
instantiation = false
filament_type = EVA
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0

[filament:fdm_filament_hips]
inherits = fdm_filament_common
from = system
filament_id = OGFS98
instantiation = false
cool_plate_temp = 0
eng_plate_temp = 90
hot_plate_temp = 90
textured_plate_temp = 90
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp_initial_layer = 90
hot_plate_temp_initial_layer = 90
textured_plate_temp_initial_layer = 90
fan_cooling_layer_time = 10
filament_max_volumetric_speed = 8
filament_type = HIPS
filament_density = 1.06
filament_cost = 22.99
nozzle_temperature_initial_layer = 240
fan_max_speed = 60
fan_min_speed = 0
overhang_fan_threshold = 25%
overhang_fan_speed = 80
nozzle_temperature = 240
nozzle_temperature_range_low = 220
nozzle_temperature_range_high = 270
slow_down_min_speed = 10
slow_down_layer_time = 6
additional_cooling_fan_speed = 0

[filament:fdm_filament_pa]
inherits = fdm_filament_common
from = system
filament_id = OGFN99
instantiation = false
activate_air_filtration = 0
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
fan_cooling_layer_time = 4
fan_max_speed = 60
fan_min_speed = 0
filament_cost = 20
filament_density = 1.04
filament_max_volumetric_speed = 8
filament_type = PA
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 280
nozzle_temperature_initial_layer = 280
nozzle_temperature_range_high = 300
nozzle_temperature_range_low = 260
overhang_fan_speed = 30
required_nozzle_HRC = 40
slow_down_layer_time = 2
slow_down_min_speed = 10
temperature_vitrification = 108
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:fdm_filament_paht]
inherits = fdm_filament_common
from = system
instantiation = false
filament_max_volumetric_speed = 12
filament_type = PAHT
filament_density = 1.24
filament_cost = 0
cool_plate_temp = 35
eng_plate_temp = 0
textured_plate_temp = 60
cool_plate_temp_initial_layer = 35
eng_plate_temp_initial_layer = 0
textured_plate_temp_initial_layer = 60
nozzle_temperature_initial_layer = 220
reduce_fan_stop_start_freq = 1
overhang_fan_threshold = 50%
close_fan_the_first_x_layers = 1
nozzle_temperature = 220
temperature_vitrification = 45
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
slow_down_min_speed = 20
additional_cooling_fan_speed = 0
fan_cooling_layer_time = 80
fan_min_speed = 50
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
slow_down_layer_time = 8
filament_start_gcode = ; Filament start gcode

filament_end_gcode = ; filament end gcode 

filament_vendor = Generic

[filament:fdm_filament_pc]
inherits = fdm_filament_common
from = system
filament_id = OGFC99
instantiation = false
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 110
eng_plate_temp_initial_layer = 110
fan_cooling_layer_time = 30
fan_max_speed = 60
fan_min_speed = 10
filament_cost = 20
filament_density = 1.04
filament_type = PC
hot_plate_temp = 110
hot_plate_temp_initial_layer = 110
nozzle_temperature = 280
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_high = 290
nozzle_temperature_range_low = 260
overhang_fan_speed = 60
overhang_fan_threshold = 25%
reduce_fan_stop_start_freq = 1
slow_down_layer_time = 2
slow_down_min_speed = 10
temperature_vitrification = 120
textured_plate_temp = 110
textured_plate_temp_initial_layer = 110
filament_max_volumetric_speed = 12
filament_flow_ratio = 0.94

[filament:fdm_filament_pctg]
inherits = fdm_filament_common
from = system
filament_id = OGFG97
instantiation = false
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 20
fan_min_speed = 20
filament_cost = 30
filament_density = 1.27
filament_max_volumetric_speed = 12
filament_type = PCTG
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
nozzle_temperature = 255
nozzle_temperature_initial_layer = 255
nozzle_temperature_range_high = 260
nozzle_temperature_range_low = 220
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
temperature_vitrification = 70
textured_plate_temp = 80
textured_plate_temp_initial_layer = 80

[filament:fdm_filament_pe]
inherits = fdm_filament_common
from = system
filament_id = OGFP99
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 20
filament_density = 1.24
filament_max_volumetric_speed = 12
filament_type = PE
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:fdm_filament_pet]
inherits = fdm_filament_common
from = system
filament_id = OGFG99
instantiation = false
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 20
fan_min_speed = 20
filament_cost = 30
filament_density = 1.27
filament_max_volumetric_speed = 10
filament_type = PETG
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
nozzle_temperature = 255
nozzle_temperature_initial_layer = 255
nozzle_temperature_range_high = 260
nozzle_temperature_range_low = 220
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 70
supertack_plate_temp_initial_layer = 70
temperature_vitrification = 70
textured_plate_temp = 80
textured_plate_temp_initial_layer = 80

[filament:fdm_filament_pha]
inherits = fdm_filament_common
from = system
filament_id = OGFR98
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 27.99
filament_density = 1.24
filament_max_volumetric_speed = 6
filament_type = PHA
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 120
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:fdm_filament_pla]
inherits = fdm_filament_common
from = system
filament_id = OGFL99
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 20
filament_density = 1.24
filament_max_volumetric_speed = 12
filament_scarf_seam_type = none
filament_scarf_gap = 15%
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 240
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55
filament_flow_ratio = 0.98

[filament:fdm_filament_pp]
inherits = fdm_filament_common
from = system
filament_id = OGFP97
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 34.99
filament_density = 0.93
filament_max_volumetric_speed = 12
filament_type = PP
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 235
nozzle_temperature_initial_layer = 235
nozzle_temperature_range_high = 250
nozzle_temperature_range_low = 220
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 110
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:fdm_filament_ppa]
inherits = fdm_filament_common
from = system
filament_id = OGFN97
instantiation = false
activate_air_filtration = 0
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 20
filament_density = 1.17
filament_flow_ratio = 0.96
filament_max_volumetric_speed = 8
filament_type = PPA-CF
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 290
nozzle_temperature_initial_layer = 290
nozzle_temperature_range_high = 320
nozzle_temperature_range_low = 280
overhang_fan_speed = 40
overhang_fan_threshold = 0%
required_nozzle_HRC = 40
slow_down_layer_time = 2
slow_down_min_speed = 10
temperature_vitrification = 210
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:fdm_filament_pps]
inherits = fdm_filament_common
from = system
instantiation = false
chamber_temperatures = 60
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 110
eng_plate_temp_initial_layer = 110
fan_cooling_layer_time = 5
fan_max_speed = 50
fan_min_speed = 0
filament_density = 1.36
filament_flow_ratio = 0.96
filament_max_volumetric_speed = 4
filament_type = PPS
hot_plate_temp = 110
hot_plate_temp_initial_layer = 110
nozzle_temperature = 320
nozzle_temperature_initial_layer = 320
nozzle_temperature_range_high = 340
nozzle_temperature_range_low = 300
overhang_fan_speed = 30
overhang_fan_threshold = 0%
slow_down_layer_time = 2
temperature_vitrification = 125
textured_plate_temp = 110
textured_plate_temp_initial_layer = 110

[filament:fdm_filament_pva]
inherits = fdm_filament_common
from = system
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
cool_plate_temp = 45
cool_plate_temp_initial_layer = 45
eng_plate_temp = 0
eng_plate_temp_initial_layer = 0
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 20
filament_density = 1.24
filament_is_support = 1
filament_max_volumetric_speed = 12
filament_soluble = 1
filament_type = PVA
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_threshold = 50%
reduce_fan_stop_start_freq = 1
supertack_plate_temp = 35
supertack_plate_temp_initial_layer = 35
slow_down_layer_time = 4
slow_down_min_speed = 10
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55
filament_flow_ratio = 0.95

[filament:fdm_filament_sbs]
inherits = fdm_filament_common
from = system
filament_id = OFLSBS99
instantiation = false
fan_cooling_layer_time = 100
filament_max_volumetric_speed = 12
filament_type = SBS
filament_density = 1.02
filament_cost = 15
cool_plate_temp = 70
eng_plate_temp = 70
hot_plate_temp = 70
textured_plate_temp = 70
cool_plate_temp_initial_layer = 70
eng_plate_temp_initial_layer = 70
hot_plate_temp_initial_layer = 70
textured_plate_temp_initial_layer = 70
nozzle_temperature_initial_layer = 235
reduce_fan_stop_start_freq = 0
fan_min_speed = 0
overhang_fan_threshold = 50%
close_fan_the_first_x_layers = 3
nozzle_temperature = 235
temperature_vitrification = 70
nozzle_temperature_range_low = 215
nozzle_temperature_range_high = 250
slow_down_min_speed = 10
slow_down_layer_time = 4
additional_cooling_fan_speed = 40

[filament:fdm_filament_tpu]
inherits = fdm_filament_common
from = system
instantiation = false
additional_cooling_fan_speed = 70
close_fan_the_first_x_layers = 1
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
cool_plate_temp = 30
cool_plate_temp_initial_layer = 30
eng_plate_temp = 30
eng_plate_temp_initial_layer = 30
fan_cooling_layer_time = 100
fan_min_speed = 100
filament_cost = 20
filament_density = 1.24
filament_max_volumetric_speed = 3.2
filament_retraction_length = 0.4
filament_type = TPU
hot_plate_temp = 35
hot_plate_temp_initial_layer = 35
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
nozzle_temperature_range_high = 250
nozzle_temperature_range_low = 200
reduce_fan_stop_start_freq = 1
temperature_vitrification = 30
textured_plate_temp = 35
textured_plate_temp_initial_layer = 35

[filament:FusRock ABS-GF @System]
inherits = FusRock ABS-GF @base
from = system
setting_id = OGFSB50_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = OGFB00
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 24.99
filament_flow_ratio = 0.95
filament_vendor = Bambu Lab

[filament:Bambu ABS-GF @base]
inherits = fdm_filament_abs
from = system
filament_id = OGFB50
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
fan_cooling_layer_time = 12
fan_max_speed = 30
filament_cost = 29.99
filament_density = 1.08
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = ABS-GF
filament_vendor = Bambu Lab
overhang_fan_speed = 30
overhang_fan_threshold = 10%
slow_down_layer_time = 4

[filament:Bambu Support for ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = OGFS06
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
fan_max_speed = 30
filament_cost = 29.98
filament_flow_ratio = 0.95
filament_is_support = 1
filament_max_volumetric_speed = 6
filament_vendor = Bambu Lab
nozzle_temperature_range_high = 270
slow_down_layer_time = 12
filament_scarf_seam_type = none
temperature_vitrification = 90

[filament:COEX ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = CXABSB01
instantiation = false
filament_vendor = COEX 3D
filament_cost = 30.00
filament_density = 1.04
filament_type = ABS
nozzle_temperature = 255
nozzle_temperature_initial_layer = 255
bed_temperature = 100
bed_temperature_initial_layer = 100
temperature_vitrification = 100
chamber_temperature = 0
filament_max_volumetric_speed = 16
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 2.5
filament_retraction_speed = 40
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 0
fan_max_speed = 30
disable_fan_first_layers = 3
full_fan_speed_layer = 0
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.04
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX ABS PRIME @base]
inherits = fdm_filament_abs
from = system
filament_id = CXABPB09
instantiation = false
filament_vendor = COEX 3D
filament_cost = 39.00
filament_density = 1.04
filament_type = ABS
nozzle_temperature = 255
nozzle_temperature_initial_layer = 255
bed_temperature = 100
bed_temperature_initial_layer = 100
temperature_vitrification = 100
chamber_temperature = 0
filament_max_volumetric_speed = 16
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 2.5
filament_retraction_speed = 40
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 0
fan_max_speed = 30
disable_fan_first_layers = 3
full_fan_speed_layer = 0
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.04
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Elegoo ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = EABSB00
instantiation = false
filament_vendor = Elegoo
filament_density = 1.1
filament_max_volumetric_speed = 12
nozzle_temperature = 270
fan_cooling_layer_time = 35

[filament:Eolas Prints ABS @System]
filament_id = GFSEP017
setting_id = GFSEP017_00
from = system
instantiation = true
inherits = fdm_filament_abs
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = ABS
nozzle_temperature = 255
nozzle_temperature_initial_layer = 260
nozzle_temperature_range_low = 240
nozzle_temperature_range_high = 270
hot_plate_temp = 100
hot_plate_temp_initial_layer = 105
chamber_temperature = 40
filament_density = 1.04
filament_cost = 19.50
filament_spool_weight = 900
filament_max_volumetric_speed = 18

[filament:FDplast ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = FDPLAST01
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 11
default_filament_colour = 
filament_vendor = FDplast
filament_flow_ratio = 0.95
nozzle_temperature_range_high = 260
nozzle_temperature_range_low = 245

[filament:Generic ABS @System]
renamed_from = My Generic ABS
inherits = fdm_filament_abs
from = system
setting_id = OGFSA04
filament_id = OGFB99
instantiation = true
compatible_printers =

[filament:NIT ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = NIT01
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 10
default_filament_colour = 
filament_flow_ratio = 0.95
filament_vendor = NIT

[filament:Overture ABS Basic @base]
inherits = fdm_filament_abs
from = system
filament_id = OVTABS08
instantiation = false
description = Overture ABS settings from https://overture3d.com/.
activate_air_filtration = 1
additional_cooling_fan_speed = 0
chamber_temperatures = 0
close_fan_the_first_x_layers = 3
compatible_printers = 
complete_print_exhaust_fan_speed = 70
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
default_filament_colour = 
during_print_exhaust_fan_speed = 70
enable_overhang_bridge_fan = 1
enable_pressure_advance = 0
eng_plate_temp = 90
eng_plate_temp_initial_layer = 90
fan_cooling_layer_time = 38
fan_max_speed = 50
fan_min_speed = 10
filament_cost = 0
filament_density = 1.15
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_end_gcode = ; filament end gcode 
M106 P3 S0

filament_flow_ratio = 0.95
filament_is_support = 0
filament_long_retractions_when_cut = nil
filament_max_volumetric_speed = 16
filament_minimal_purge_on_wipe_tower = 15
filament_notes = 
filament_retract_before_wipe = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = nil
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_settings_id = OVERTURE ABS Basic
filament_soluble = 0
filament_start_gcode = ; Filament gcode
{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}
filament_type = ABS
filament_vendor = Overture
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
hot_plate_temp = 90
hot_plate_temp_initial_layer = 90
nozzle_temperature = 260
nozzle_temperature_initial_layer = 260
nozzle_temperature_range_high = 265
nozzle_temperature_range_low = 245
overhang_fan_speed = 100
overhang_fan_threshold = 95%
pressure_advance = 0.02
reduce_fan_stop_start_freq = 1
required_nozzle_HRC = 3
slow_down_for_layer_cooling = 1
slow_down_layer_time = 2
slow_down_min_speed = 20
temperature_vitrification = 103
textured_plate_temp = 90
textured_plate_temp_initial_layer = 90

[filament:PolyLite ABS @base]
inherits = fdm_filament_abs
from = system
filament_id = OGFB60
instantiation = false
filament_cost = 26.9
filament_density = 1.03
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = Polymaker

[filament:Bambu ASA @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFB01
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
fan_max_speed = 35
filament_cost = 31.99
filament_density = 1.05
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = Bambu Lab
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
slow_down_layer_time = 12
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:Bambu ASA-Aero @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFB02
instantiation = false
description = This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide.
fan_cooling_layer_time = 30
fan_max_speed = 50
fan_min_speed = 30
filament_cost = 49.99
filament_density = 0.99
filament_flow_ratio = 0.52
filament_max_volumetric_speed = 12
filament_retraction_length = 1.5
filament_type = ASA-AERO
filament_vendor = Bambu Lab
filament_wipe_distance = 5
filament_z_hop_types = Normal Lift
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
overhang_fan_speed = 50
reduce_fan_stop_start_freq = 0
slow_down_layer_time = 5
filament_scarf_seam_type = none

[filament:Bambu ASA-CF @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFB51
instantiation = false
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
fan_max_speed = 25
filament_cost = 36.99
filament_density = 1.02
filament_flow_ratio = 0.9
filament_max_volumetric_speed = 12
filament_type = ASA-CF
filament_vendor = Bambu Lab
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 275
nozzle_temperature_initial_layer = 275
nozzle_temperature_range_low = 250
slow_down_layer_time = 12
temperature_vitrification = 108
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:COEX ASA PRIME @base]
inherits = fdm_filament_asa
from = system
filament_id = CXASAB04
instantiation = false
filament_vendor = COEX 3D
filament_cost = 34.00
filament_density = 1.07
filament_type = ASA
filament_notes = UV and weather resistant - requires good ventilation
nozzle_temperature = 265
nozzle_temperature_initial_layer = 265
bed_temperature = 100
bed_temperature_initial_layer = 100
temperature_vitrification = 95
chamber_temperature = 0
filament_max_volumetric_speed = 16
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 2.5
filament_retraction_speed = 40
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 0
fan_max_speed = 30
disable_fan_first_layers = 3
full_fan_speed_layer = 0
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.04
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Elas ASA @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFB01
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
activate_air_filtration = 0
activate_chamber_temp_control = 0
adaptive_pressure_advance = 0
adaptive_pressure_advance_bridges = 0
adaptive_pressure_advance_model = 0,0,0
0,0,0
adaptive_pressure_advance_overhangs = 0
additional_cooling_fan_speed = 0
chamber_temperature = 65
close_fan_the_first_x_layers = 3
complete_print_exhaust_fan_speed = 80
cool_plate_temp = 110
cool_plate_temp_initial_layer = 110
default_filament_colour = 
dont_slow_down_outer_wall = 0
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
fan_cooling_layer_time = 35
fan_max_speed = 35
fan_min_speed = 10
filament_cooling_final_speed = 0
filament_cooling_initial_speed = 0
filament_cooling_moves = 0
filament_cost = 599
filament_density = 1.04
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_flow_ratio = 0.95
filament_is_support = 0
filament_loading_speed = 0
filament_loading_speed_start = 0
filament_long_retractions_when_cut = nil
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = 
filament_retract_before_wipe = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = nil
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_soluble = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 0
filament_toolchange_delay = 0
filament_unloading_speed = 0
filament_unloading_speed_start = 0
filament_vendor = Elas
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
idle_temperature = 0
internal_bridge_fan_speed = -1
ironing_fan_speed = -1
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_high = 280
nozzle_temperature_range_low = 240
overhang_fan_speed = 80
overhang_fan_threshold = 25%
pellet_flow_coefficient = 0.4157
pressure_advance = 0.075
reduce_fan_stop_start_freq = 1
required_nozzle_HRC = 0
slow_down_for_layer_cooling = 1
slow_down_layer_time = 12
slow_down_min_speed = 20
supertack_plate_temp = 35
supertack_plate_temp_initial_layer = 35
support_material_interface_fan_speed = -1
temperature_vitrification = 100
textured_cool_plate_temp = 40
textured_cool_plate_temp_initial_layer = 40
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:Elegoo ASA @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFE06
instantiation = false
filament_vendor = Elegoo
filament_density = 1.1
filament_max_volumetric_speed = 12

[filament:Eolas Prints ASA @System]
filament_id = GFSEP018
setting_id = GFSEP018_00
from = system
instantiation = true
inherits = fdm_filament_asa
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = ASA
nozzle_temperature = 260
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_low = 245
nozzle_temperature_range_high = 275
hot_plate_temp = 100
hot_plate_temp_initial_layer = 105
chamber_temperature = 40
filament_density = 1.07
filament_cost = 22.50
filament_spool_weight = 900
filament_max_volumetric_speed = 18

[filament:Generic ASA @System]
renamed_from = My Generic ASA
inherits = fdm_filament_asa
from = system
setting_id = OGFSA04
filament_id = OGFB98
instantiation = true
compatible_printers =

[filament:Overture ASA @base]
inherits = fdm_filament_asa
from = system
filament_id = GFOT009
instantiation = false
fan_cooling_layer_time = 45
fan_max_speed = 60
fan_min_speed = 10
filament_cost = 29.99
filament_density = 1.14
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 10
filament_vendor = Overture
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 240
slow_down_layer_time = 2
temperature_vitrification = 106
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:PolyLite ASA @base]
inherits = fdm_filament_asa
from = system
filament_id = OGFB61
instantiation = false
eng_plate_temp = 100
eng_plate_temp_initial_layer = 100
filament_cost = 23.6
filament_density = 1.02
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = Polymaker
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:Generic BVOH @System]
inherits = fdm_filament_bvoh
from = system
setting_id = OGFSS97_00
instantiation = true
compatible_printers =

[filament:Generic CoPE @System]
inherits = fdm_filament_cope
from = system
setting_id = OGFSC99_00
instantiation = true
compatible_printers =

[filament:Generic EVA @System]
inherits = fdm_filament_eva
from = system
setting_id = OGFSR99_00
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
compatible_printers =

[filament:FDplast HIPS @base]
inherits = fdm_filament_hips
from = system
filament_id = FDPLAST02
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 11
filament_density = 1.26
filament_flow_ratio = 0.98
filament_vendor = FDplast
nozzle_temperature = 250
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 250
hot_plate_temp = 110
hot_plate_temp_initial_layer = 110
textured_plate_temp = 110
textured_plate_temp_initial_layer = 110

[filament:Generic HIPS @System]
inherits = fdm_filament_hips
from = system
setting_id = OGFSS98_00
instantiation = true
compatible_printers =

[filament:AliZ PA-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = AliZ003
instantiation = false
filament_type = PA-CF
complete_print_exhaust_fan_speed = 80
during_print_exhaust_fan_speed = 60
enable_pressure_advance = 0
eng_plate_temp = 80
eng_plate_temp_initial_layer = 80
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 49.9
filament_flow_ratio = 1
filament_max_volumetric_speed = 8
filament_vendor = Aliz
full_fan_speed_layer = 2
nozzle_temperature = 290
nozzle_temperature_initial_layer = 290
nozzle_temperature_range_high = 300
nozzle_temperature_range_low = 260
overhang_fan_speed = 40
overhang_fan_threshold = 0%
pressure_advance = 0.026
slow_down_layer_time = 2
slow_down_min_speed = 10

[filament:Bambu PA-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFN03
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 84.99
filament_density = 1.09
filament_flow_ratio = 0.96
filament_type = PA-CF
filament_vendor = Bambu Lab
nozzle_temperature = 280
nozzle_temperature_initial_layer = 280
overhang_fan_speed = 40
overhang_fan_threshold = 0%
temperature_vitrification = 170

[filament:Bambu PA6-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFN05
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 79.99
filament_density = 1.10
filament_flow_ratio = 0.96
filament_type = PA6-CF
filament_vendor = Bambu Lab
nozzle_temperature = 275
nozzle_temperature_initial_layer = 275
overhang_fan_speed = 40
overhang_fan_threshold = 0%
temperature_vitrification = 170

[filament:Bambu PA6-GF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFN08
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 59.99
filament_density = 1.14
filament_flow_ratio = 0.96
filament_type = PA-GF
filament_vendor = Bambu Lab
full_fan_speed_layer = 2
overhang_fan_speed = 40
overhang_fan_threshold = 0%
temperature_vitrification = 180

[filament:Bambu PAHT-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFN04
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 94.99
filament_density = 1.06
filament_flow_ratio = 0.96
filament_type = PA-CF
filament_vendor = Bambu Lab
full_fan_speed_layer = 2
overhang_fan_speed = 40
overhang_fan_threshold = 0%
temperature_vitrification = 180

[filament:Bambu Support For PA/PET @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFS03
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
fan_cooling_layer_time = 10
filament_cost = 34.99
filament_density = 1.22
filament_is_support = 1
filament_vendor = Bambu Lab
nozzle_temperature = 280
nozzle_temperature_initial_layer = 280
required_nozzle_HRC = 3
slow_down_layer_time = 6

[filament:Bambu Support G @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFS01
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
fan_cooling_layer_time = 10
filament_cost = 34.99
filament_density = 1.22
filament_is_support = 1
filament_vendor = Bambu Lab
nozzle_temperature = 280
nozzle_temperature_initial_layer = 280
required_nozzle_HRC = 3
filament_scarf_seam_type = none
slow_down_layer_time = 6

[filament:COEX NYLEX PA6-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = CXPACB23
instantiation = false
filament_vendor = COEX 3D
filament_cost = 85.00
filament_density = 1.24
filament_type = PA-CF
nozzle_temperature = 285
nozzle_temperature_initial_layer = 285
bed_temperature = 100
bed_temperature_initial_layer = 100
temperature_vitrification = 170
chamber_temperature = 60
filament_max_volumetric_speed = 11
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 2.5
filament_retraction_speed = 40
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 0
fan_max_speed = 30
disable_fan_first_layers = 4
full_fan_speed_layer = 0
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.02
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX NYLEX UNFILLED @base]
inherits = fdm_filament_pa
from = system
filament_id = CXPAUB21
instantiation = false
filament_vendor = COEX 3D
filament_cost = 85.00
filament_density = 1.08
filament_type = PA
nozzle_temperature = 260
nozzle_temperature_initial_layer = 260
bed_temperature = 100
bed_temperature_initial_layer = 100
temperature_vitrification = 100
chamber_temperature = 0
filament_max_volumetric_speed = 11
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 2.5
filament_retraction_speed = 40
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 0
fan_max_speed = 30
disable_fan_first_layers = 4
full_fan_speed_layer = 0
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.02
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Fiberon PA12-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFL52
instantiation = false
eng_plate_temp = 40
eng_plate_temp_initial_layer = 40
fan_cooling_layer_time = 15
fan_max_speed = 100
filament_cost = 99.99
filament_density = 1.06
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 14
filament_type = PA-CF
filament_vendor = Polymaker
full_fan_speed_layer = 2
hot_plate_temp = 40
hot_plate_temp_initial_layer = 40
nozzle_temperature = 300
nozzle_temperature_initial_layer = 300
nozzle_temperature_range_low = 260
overhang_fan_speed = 100
reduce_fan_stop_start_freq = 1
temperature_vitrification = 131
textured_plate_temp = 40
textured_plate_temp_initial_layer = 40

[filament:Fiberon PA6-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFL50
instantiation = false
eng_plate_temp = 40
eng_plate_temp_initial_layer = 40
fan_cooling_layer_time = 15
fan_max_speed = 100
filament_cost = 83.99
filament_density = 1.17
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = PA6-CF
filament_vendor = Polymaker
hot_plate_temp = 40
hot_plate_temp_initial_layer = 40
nozzle_temperature = 300
nozzle_temperature_initial_layer = 300
nozzle_temperature_range_low = 280
overhang_fan_speed = 100
reduce_fan_stop_start_freq = 1
temperature_vitrification = 215
textured_plate_temp = 40
textured_plate_temp_initial_layer = 40

[filament:Fiberon PA6-GF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFL51
instantiation = false
eng_plate_temp = 40
eng_plate_temp_initial_layer = 40
fan_cooling_layer_time = 15
fan_max_speed = 100
filament_cost = 63.99
filament_density = 1.2
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = PA-GF
filament_vendor = Polymaker
full_fan_speed_layer = 2
hot_plate_temp = 40
hot_plate_temp_initial_layer = 40
nozzle_temperature = 300
nozzle_temperature_initial_layer = 300
nozzle_temperature_range_low = 280
overhang_fan_speed = 100
reduce_fan_stop_start_freq = 1
temperature_vitrification = 191
textured_plate_temp = 40
textured_plate_temp_initial_layer = 40

[filament:Fiberon PA612-CF @base]
inherits = fdm_filament_pa
from = system
filament_id = OGFL53
instantiation = false
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 94.99
filament_density = 1.06
filament_flow_ratio = 0.96
filament_vendor = Polymaker
full_fan_speed_layer = 2
overhang_fan_speed = 40
overhang_fan_threshold = 0%
temperature_vitrification = 180

[filament:Generic PA @System]
renamed_from = My Generic PA
inherits = fdm_filament_pa
from = system
setting_id = OGFSA04
filament_id = OGFN99
instantiation = true
compatible_printers =

[filament:Generic PA-CF @System]
renamed_from = My Generic PA-CF
inherits = fdm_filament_pa
from = system
setting_id = OGFSA04
filament_id = OGFN98
instantiation = true
filament_type = PA-CF
compatible_printers =

[filament:Elegoo PAHT @base]
inherits = fdm_filament_paht
from = system
filament_id = EPAHTB00
instantiation = false
filament_cost = 0
filament_density = 1.25
filament_max_volumetric_speed = 16
filament_vendor = Elegoo
filament_start_gcode = ; filament start gcode

[filament:Bambu PC @base]
inherits = fdm_filament_pc
from = system
filament_id = OGFC00
instantiation = false
filament_vendor = Bambu Lab
filament_cost = 39.99
filament_flow_ratio = 0.94

[filament:Bambu PC FR @base]
inherits = fdm_filament_pc
from = system
filament_id = OGFC01
instantiation = false
filament_cost = 0
filament_density = 1.19
filament_flow_ratio = 0.94
filament_vendor = Bambu Lab

[filament:Elegoo PC @base]
inherits = fdm_filament_pc
from = system
filament_id = EPCB00
instantiation = false
filament_cost = 0
filament_density = 1.25
filament_max_volumetric_speed = 16
filament_vendor = Elegoo
filament_start_gcode = ; filament start gcode

[filament:Generic PC @System]
renamed_from = My Generic PC
inherits = fdm_filament_pc
from = system
setting_id = OGFSA04
filament_id = OGFC99
instantiation = true
compatible_printers =

[filament:COEX PCTG PRIME @base]
inherits = fdm_filament_pctg
from = system
filament_id = CXPCTB15
instantiation = false
filament_vendor = COEX 3D
filament_cost = 38.00
filament_density = 1.27
filament_type = PCTG
filament_notes = High clarity and chemical resistance copolyester
nozzle_temperature = 275
nozzle_temperature_initial_layer = 275
bed_temperature = 80
bed_temperature_initial_layer = 85
temperature_vitrification = 80
filament_max_volumetric_speed = 12
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 3.5
filament_retraction_speed = 35
filament_deretraction_speed = 35
filament_z_hop = 0.4
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 30
fan_max_speed = 50
disable_fan_first_layers = 2
full_fan_speed_layer = 4
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.045
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Generic PCTG @System]
inherits = fdm_filament_pctg
from = system
setting_id = OGFSG97_00
instantiation = true
compatible_printers =

[filament:Generic PE @System]
inherits = fdm_filament_pe
from = system
setting_id = OGFSP99_00
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
compatible_printers =

[filament:Generic PE-CF @System]
inherits = fdm_filament_pe
from = system
setting_id = OGFSP98_00
instantiation = true
compatible_printers =

[filament:AliZ PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = AliZ001
instantiation = false
close_fan_the_first_x_layers = 2
enable_pressure_advance = 0
fan_max_speed = 80
fan_min_speed = 30
filament_cost = 49.9
filament_flow_ratio = 1
filament_max_volumetric_speed = 15
filament_vendor = Aliz
hot_plate_temp = 79
hot_plate_temp_initial_layer = 79
nozzle_temperature = 250
nozzle_temperature_initial_layer = 250
overhang_fan_threshold = 25%
pressure_advance = 0.036
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Bambu PET-CF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFT01
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 80
eng_plate_temp_initial_layer = 80
fan_cooling_layer_time = 5
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 84.99
filament_density = 1.29
filament_max_volumetric_speed = 8
filament_type = PET-CF
filament_vendor = Bambu Lab
hot_plate_temp = 100
hot_plate_temp_initial_layer = 100
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_high = 290
nozzle_temperature_range_low = 260
overhang_fan_speed = 40
overhang_fan_threshold = 0%
required_nozzle_HRC = 40
supertack_plate_temp = 80
supertack_plate_temp_initial_layer = 80
slow_down_layer_time = 2
temperature_vitrification = 185
textured_plate_temp = 100
textured_plate_temp_initial_layer = 100

[filament:Bambu PETG Basic @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG00
instantiation = false
description = To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 30
fan_max_speed = 40
fan_min_speed = 10
filament_cost = 24.99
filament_density = 1.25
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 8
filament_vendor = Bambu Lab
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 230
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Bambu PETG HF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG02
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 30
fan_max_speed = 40
fan_min_speed = 10
filament_cost = 24.99
filament_density = 1.28
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = Bambu Lab
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature = 245
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 230
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Bambu PETG Translucent @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG01
instantiation = false
description = To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 30
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 24.99
filament_density = 1.25
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 6
filament_vendor = Bambu Lab
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature = 245
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 230
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Bambu PETG-CF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG50
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_max_speed = 30
fan_min_speed = 0
filament_cost = 34.99
filament_density = 1.25
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = PETG-CF
filament_vendor = Bambu Lab
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 240
overhang_fan_speed = 90
overhang_fan_threshold = 10%
required_nozzle_HRC = 40
slow_down_layer_time = 6
temperature_vitrification = 70
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:COEX PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = CXPETB13
instantiation = false
filament_vendor = COEX 3D
filament_cost = 33.00
filament_density = 1.27
filament_type = PETG
filament_notes = IMPORTANT: Set travel speed to maximum your machine allows (200-500mm/s) to reduce stringing
nozzle_temperature = 245
nozzle_temperature_initial_layer = 250
bed_temperature = 80
bed_temperature_initial_layer = 85
temperature_vitrification = 70
filament_max_volumetric_speed = 12
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 4
filament_retraction_speed = 30
filament_deretraction_speed = 30
filament_z_hop = 0.4
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 30
fan_max_speed = 50
disable_fan_first_layers = 2
full_fan_speed_layer = 4
slow_down_layer_time = 5
slow_down_min_speed = 10
enable_pressure_advance = 1
pressure_advance = 0.045
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Elas PETG Basic @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG00
instantiation = false
description = To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.
complete_print_exhaust_fan_speed = 80
cool_plate_temp = 60
cool_plate_temp_initial_layer = 60
dont_slow_down_outer_wall = 0
during_print_exhaust_fan_speed = 60
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
eng_plate_temp = 80
eng_plate_temp_initial_layer = 80
fan_cooling_layer_time = 20
fan_max_speed = 100
fan_min_speed = 20
filament_cooling_final_speed = 0
filament_cooling_initial_speed = 0
filament_cooling_moves = 0
filament_cost = 445
filament_density = 1.27
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_flow_ratio = 1
filament_is_support = 0
filament_loading_speed = 0
filament_loading_speed_start = 0
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 18
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = 
filament_retract_before_wipe = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = 18
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_shrink = 99.7%
filament_shrinkage_compensation_z = 100%
filament_soluble = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 0
filament_toolchange_delay = 0
filament_unloading_speed = 0
filament_unloading_speed_start = 0
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
idle_temperature = 0
internal_bridge_fan_speed = -1
ironing_fan_speed = -1
filament_vendor = Elas
nozzle_temperature = 250
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 230
overhang_fan_speed = 100
overhang_fan_threshold = 10%
pellet_flow_coefficient = 0.4157
pressure_advance = 0.035
reduce_fan_stop_start_freq = 1
required_nozzle_HRC = 3
slow_down_for_layer_cooling = 1
slow_down_layer_time = 8
slow_down_min_speed = 10
supertack_plate_temp = 70
supertack_plate_temp_initial_layer = 70
support_material_interface_fan_speed = -1
temperature_vitrification = 70
textured_cool_plate_temp = 40
textured_cool_plate_temp_initial_layer = 40
textured_plate_temp = 70
textured_plate_temp_initial_layer = 80

[filament:Elegoo PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = EPETGB00
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 30
fan_max_speed = 40
fan_min_speed = 10
filament_cost = 0
filament_density = 1.25
filament_max_volumetric_speed = 8
filament_vendor = Elegoo
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 230
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70
filament_start_gcode = ; Filament start gcode

filament_end_gcode = ; filament end gcode 

filament_type = PETG

[filament:Elegoo PETG PRO @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFE02
instantiation = false
filament_cost = 12.49
filament_density = 1.27
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_retraction_length = 0.8
filament_retraction_speed = 45
filament_deretraction_speed = 45
filament_vendor = Elegoo
nozzle_temperature = 245
nozzle_temperature_initial_layer = 240
nozzle_temperature_range_high = 260
nozzle_temperature_range_low = 230
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
textured_plate_temp = 75
textured_plate_temp_initial_layer = 75
overhang_fan_speed = 90
fan_max_speed = 80
fan_min_speed = 20
fan_cooling_layer_time = 20
slow_down_layer_time = 10
slow_down_min_speed = 20

[filament:Elegoo PETG-CF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFE03
instantiation = false
filament_cost = 18.99
filament_density = 1.29
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 10
filament_retraction_length = 0.8
filament_retraction_speed = 45
filament_deretraction_speed = 45
filament_vendor = Elegoo
nozzle_temperature = 255
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 240
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
textured_plate_temp = 75
textured_plate_temp_initial_layer = 75
overhang_fan_speed = 90
fan_max_speed = 80
fan_min_speed = 20
fan_cooling_layer_time = 20
slow_down_layer_time = 10
slow_down_min_speed = 20

[filament:Elegoo Rapid PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFE01
instantiation = false
filament_cost = 13.99
filament_density = 1.28
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 20
filament_retraction_length = 0.8
filament_retraction_speed = 45
filament_deretraction_speed = 45
filament_vendor = Elegoo
nozzle_temperature = 255
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 240
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70
overhang_fan_speed = 90
fan_max_speed = 80
fan_min_speed = 20
fan_cooling_layer_time = 20
slow_down_layer_time = 10
slow_down_min_speed = 20

[filament:Eolas Prints PETG @System]
filament_id = GFSEP010
setting_id = GFSEP010_00
from = system
instantiation = true
inherits = fdm_filament_pet
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PETG
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_low = 230
nozzle_temperature_range_high = 260
hot_plate_temp = 80
hot_plate_temp_initial_layer = 85
filament_density = 1.27
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PETG Transition @System]
filament_id = GFSEP012
setting_id = GFSEP012_00
from = system
instantiation = true
inherits = fdm_filament_pet
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PETG
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_low = 230
nozzle_temperature_range_high = 260
hot_plate_temp = 80
hot_plate_temp_initial_layer = 85
filament_density = 1.27
filament_cost = 17.40
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PETG UV Resistant @System]
filament_id = GFSEP011
setting_id = GFSEP011_00
from = system
instantiation = true
inherits = fdm_filament_pet
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PETG
nozzle_temperature = 245
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_low = 235
nozzle_temperature_range_high = 265
hot_plate_temp = 80
hot_plate_temp_initial_layer = 85
filament_density = 1.27
filament_cost = 30.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:FDplast PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = FDPLAST03
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 11
default_filament_colour = 
filament_vendor = FDplast
filament_density = 1.27
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 20
fan_max_speed = 100
fan_min_speed = 30
nozzle_temperature = 235
nozzle_temperature_initial_layer = 240
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 220
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
textured_plate_temp = 80
textured_plate_temp_initial_layer = 80
compatible_printers =

[filament:Fiberon PET-CF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFL54
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 242
fan_min_speed = 0
filament_cost = 89.99
filament_density = 1.34
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = PET-CF
filament_vendor = Polymaker
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature = 300
nozzle_temperature_initial_layer = 300
nozzle_temperature_range_high = 300
nozzle_temperature_range_low = 270
required_nozzle_HRC = 40
supertack_plate_temp = 80
supertack_plate_temp_initial_layer = 80
slow_down_layer_time = 5
slow_down_min_speed = 10
temperature_vitrification = 147
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Fiberon PETG-ESD @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFL06
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 60
eng_plate_temp_initial_layer = 60
fan_cooling_layer_time = 15
fan_min_speed = 0
filament_cost = 0
filament_density = 1.24
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = Polymaker
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
nozzle_temperature = 290
nozzle_temperature_initial_layer = 290
nozzle_temperature_range_high = 290
nozzle_temperature_range_low = 250
slow_down_layer_time = 2
slow_down_min_speed = 10
temperature_vitrification = 76
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60

[filament:Fiberon PETG-rCF @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFL55
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 12
fan_min_speed = 0
filament_cost = 39.99
filament_density = 1.3
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_type = PETG-CF
filament_vendor = Polymaker
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
nozzle_temperature = 270
nozzle_temperature_initial_layer = 270
nozzle_temperature_range_high = 270
nozzle_temperature_range_low = 240
required_nozzle_HRC = 40
slow_down_layer_time = 2
slow_down_min_speed = 10
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Generic PETG @System]
renamed_from = My Generic PETG
inherits = fdm_filament_pet
from = system
setting_id = OGFSA04
filament_id = OGFG99
instantiation = true
compatible_printers =

[filament:Generic PETG HF @System]
inherits = fdm_filament_pet
from = system
setting_id = OGFSG96_00
instantiation = true
filament_max_volumetric_speed = 20
compatible_printers =

[filament:Generic PETG-CF @System]
inherits = fdm_filament_pet
from = system
setting_id = OGFSG50
instantiation = true
fan_cooling_layer_time = 30
fan_max_speed = 40
fan_min_speed = 5
filament_max_volumetric_speed = 11.5
overhang_fan_speed = 100
compatible_printers =

[filament:NIT PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = NIT03
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 12
default_filament_colour = 
filament_vendor = NIT
filament_density = 1.27
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 20
fan_max_speed = 100
fan_min_speed = 30
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_high = 250
nozzle_temperature_range_low = 230
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
textured_plate_temp = 80
textured_plate_temp_initial_layer = 80
compatible_printers =

[filament:PolyLite PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFG60
instantiation = false
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 70
eng_plate_temp_initial_layer = 70
fan_cooling_layer_time = 30
fan_max_speed = 90
fan_min_speed = 40
filament_flow_ratio = 0.95
filament_vendor = Polymaker
hot_plate_temp = 70
hot_plate_temp_initial_layer = 70
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
slow_down_min_speed = 10
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:SUNLU PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = OGFSNL08
instantiation = false
description = To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.
cool_plate_temp = 0
cool_plate_temp_initial_layer = 0
eng_plate_temp = 60
eng_plate_temp_initial_layer = 60
fan_cooling_layer_time = 30
fan_max_speed = 30
fan_min_speed = 10
filament_cost = 22.99
filament_density = 1.27
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
nozzle_temperature = 245
nozzle_temperature_initial_layer = 250
nozzle_temperature_range_high = 280
nozzle_temperature_range_low = 230
overhang_fan_speed = 90
overhang_fan_threshold = 10%
slow_down_layer_time = 12
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60
temperature_vitrification = 68

[filament:eSUN PETG @base]
inherits = fdm_filament_pet
from = system
filament_id = ESN03
instantiation = false
filament_vendor = eSUN
filament_density = 1.27
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 10
fan_max_speed = 100
fan_min_speed = 30
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
nozzle_temperature_range_high = 250
nozzle_temperature_range_low = 230
temperature_vitrification = 64
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
textured_plate_temp = 65
textured_plate_temp_initial_layer = 65
compatible_printers =

[filament:Generic PHA @System]
inherits = fdm_filament_pha
from = system
setting_id = OGFSR98_00
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
compatible_printers =

[filament:AliZ PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = AliZ002
instantiation = false
enable_pressure_advance = 0
fan_cooling_layer_time = 100
filament_cost = 69
filament_density = 1.27
filament_vendor = Aliz
filament_wipe_distance = 0
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
pressure_advance = 0.025
slow_down_layer_time = 4
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:Bambu PLA Aero @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA11
instantiation = false
description = This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: Instructions for printing RC model with foaming PLA (PLA Aero).
fan_min_speed = 30
filament_cost = 44.99
filament_density = 1.21
filament_flow_ratio = 0.6
filament_max_volumetric_speed = 6
filament_type = PLA-AERO
filament_vendor = Bambu Lab
filament_scarf_seam_type = none
nozzle_temperature_range_low = 210
nozzle_temperature_range_high = 260
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0

[filament:Bambu PLA Basic @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA00
instantiation = false
filament_cost = 24.99
filament_density = 1.26
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Bambu Lab
filament_scarf_seam_type = none
filament_scarf_height = 10%
filament_scarf_gap = 0%
filament_scarf_length = 10

[filament:Bambu PLA Dynamic @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA13
instantiation = false
filament_cost = 31.99
filament_density = 1.26
filament_vendor = Bambu Lab

[filament:Bambu PLA Galaxy @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA15
instantiation = false
filament_cost = 29.99
filament_density = 1.19
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Bambu Lab

[filament:Bambu PLA Glow @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA12
instantiation = false
filament_cost = 29.99
filament_density = 1.26
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Bambu Lab
temperature_vitrification = 45

[filament:Bambu PLA Impact @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA03
instantiation = false
filament_cost = 25.4
filament_flow_ratio = 0.95
filament_vendor = Bambu Lab

[filament:Bambu PLA Marble @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA07
instantiation = false
filament_cost = 29.99
filament_density = 1.22
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab

[filament:Bambu PLA Matte @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA01
instantiation = false
filament_cost = 24.99
filament_density = 1.32
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab
filament_scarf_seam_type = none
filament_scarf_height = 5%
filament_scarf_gap = 0%
filament_scarf_length = 10

[filament:Bambu PLA Metal @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA02
instantiation = false
description = To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.
filament_cost = 29.99
filament_density = 1.25
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab
filament_scarf_seam_type = none

[filament:Bambu PLA Silk @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA05
instantiation = false
description = To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.
filament_cost = 29.99
filament_density = 1.32
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab
filament_scarf_height = 5%
filament_scarf_gap = 0%
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0

[filament:Bambu PLA Silk+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA06
instantiation = false
description = To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.
filament_cost = 29.99
filament_density = 1.27
filament_flow_ratio = 0.98
filament_scarf_height = 5%
filament_scarf_seam_type = all
filament_vendor = Bambu Lab
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230

[filament:Bambu PLA Sparkle @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA08
instantiation = false
filament_cost = 29.99
filament_density = 1.26
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab

[filament:Bambu PLA Tough @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA09
instantiation = false
filament_cost = 28.99
filament_density = 1.26
filament_flow_ratio = 0.98
filament_vendor = Bambu Lab
filament_scarf_seam_type = none

[filament:Bambu PLA Wood @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA16
instantiation = false
filament_cost = 24.99
filament_density = 1.21
filament_flow_ratio = 0.98
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 12
filament_retraction_distances_when_cut = 18
filament_scarf_seam_type = none
filament_vendor = Bambu Lab

[filament:Bambu PLA-CF @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA50
instantiation = false
additional_cooling_fan_speed = 0
cool_plate_temp = 45
cool_plate_temp_initial_layer = 45
filament_cost = 34.99
filament_density = 1.22
filament_flow_ratio = 0.98
filament_type = PLA-CF
filament_vendor = Bambu Lab
nozzle_temperature_range_low = 210
nozzle_temperature_range_high = 250
required_nozzle_HRC = 40
supertack_plate_temp = 50
supertack_plate_temp_initial_layer = 50
slow_down_layer_time = 8

[filament:Bambu Support For PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFS02
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
cool_plate_temp = 40
cool_plate_temp_initial_layer = 40
filament_cost = 69.98
filament_density = 1.30
filament_is_support = 1
filament_vendor = Bambu Lab
filament_scarf_seam_type = none
slow_down_layer_time = 8

[filament:Bambu Support For PLA/PETG @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFS05
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
fan_cooling_layer_time = 80
fan_max_speed = 30
fan_min_speed = 20
filament_cost = 69.98
filament_density = 1.19
filament_is_support = 1
filament_max_volumetric_speed = 6
filament_scarf_seam_type = none
filament_vendor = Bambu Lab
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
nozzle_temperature = 210
nozzle_temperature_initial_layer = 210
slow_down_layer_time = 8
supertack_plate_temp_initial_layer = 0
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60

[filament:Bambu Support W @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFS00
instantiation = false
description = This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.
cool_plate_temp = 40
cool_plate_temp_initial_layer = 40
filament_cost = 69.98
filament_density = 1.30
filament_is_support = 1
filament_vendor = Bambu Lab
filament_scarf_seam_type = none
slow_down_layer_time = 8

[filament:COEX PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = CXPLAB02
instantiation = false
filament_vendor = COEX 3D
filament_cost = 24.00
filament_density = 1.24
filament_type = PLA
nozzle_temperature = 230
nozzle_temperature_initial_layer = 235
bed_temperature = 60
bed_temperature_initial_layer = 60
temperature_vitrification = 55
filament_max_volumetric_speed = 18
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 1.5
filament_retraction_speed = 45
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 100
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slow_down_layer_time = 5
slow_down_min_speed = 10
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX PLA PRIME @base]
inherits = fdm_filament_pla
from = system
filament_id = CXPLAB08
instantiation = false
filament_vendor = COEX 3D
filament_cost = 32.00
filament_density = 1.24
filament_type = PLA
filament_notes = Made with NatureWorks Ingeo 3D850 - improved heat resistance and toughness
nozzle_temperature = 235
nozzle_temperature_initial_layer = 240
bed_temperature = 60
bed_temperature_initial_layer = 60
temperature_vitrification = 60
filament_max_volumetric_speed = 15
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 1.2
filament_retraction_speed = 50
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 100
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slow_down_layer_time = 5
slow_down_min_speed = 10
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Elas PLA Basic @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA00
instantiation = false
activate_air_filtration = 0
activate_chamber_temp_control = 0
adaptive_pressure_advance = 0
adaptive_pressure_advance_bridges = 0
adaptive_pressure_advance_model = 0,0,0
0,0,0
adaptive_pressure_advance_overhangs = 0
additional_cooling_fan_speed = 70
chamber_temperature = 0
close_fan_the_first_x_layers = 1
complete_print_exhaust_fan_speed = 70
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
default_filament_colour = 
dont_slow_down_outer_wall = 0
during_print_exhaust_fan_speed = 70
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
eng_plate_temp = 55
eng_plate_temp_initial_layer = 55
fan_cooling_layer_time = 100
fan_max_speed = 80
fan_min_speed = 60
filament_cooling_final_speed = 0
filament_cooling_initial_speed = 0
filament_cooling_moves = 0
filament_cost = 449.5
filament_density = 1.24
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_flow_ratio = 0.98
filament_is_support = 0
filament_loading_speed = 0
filament_loading_speed_start = 0
filament_long_retractions_when_cut = nil
filament_max_volumetric_speed = 25
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = 
filament_retract_before_wipe = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = nil
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_soluble = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 0
filament_toolchange_delay = 0
filament_unloading_speed = 0
filament_unloading_speed_start = 0
filament_vendor = Elas
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
idle_temperature = 0
internal_bridge_fan_speed = -1
ironing_fan_speed = -1
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_speed = 100
overhang_fan_threshold = 50%
pellet_flow_coefficient = 0.4157
pressure_advance = 0.025
reduce_fan_stop_start_freq = 1
required_nozzle_HRC = 3
slow_down_for_layer_cooling = 1
slow_down_layer_time = 4
slow_down_min_speed = 20
supertack_plate_temp = 45
supertack_plate_temp_initial_layer = 45
support_material_interface_fan_speed = -1
temperature_vitrification = 45
textured_cool_plate_temp = 40
textured_cool_plate_temp_initial_layer = 40
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:Elas PLA Pro @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFA00
instantiation = false
activate_air_filtration = 0
activate_chamber_temp_control = 0
adaptive_pressure_advance = 0
adaptive_pressure_advance_bridges = 0
adaptive_pressure_advance_model = 0,0,0
0,0,0
adaptive_pressure_advance_overhangs = 0
additional_cooling_fan_speed = 70
chamber_temperature = 0
close_fan_the_first_x_layers = 1
complete_print_exhaust_fan_speed = 70
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
default_filament_colour = 
dont_slow_down_outer_wall = 0
during_print_exhaust_fan_speed = 70
enable_overhang_bridge_fan = 1
enable_pressure_advance = 1
eng_plate_temp = 60
eng_plate_temp_initial_layer = 60
fan_cooling_layer_time = 100
fan_max_speed = 100
fan_min_speed = 100
filament_cooling_final_speed = 0
filament_cooling_initial_speed = 0
filament_cooling_moves = 0
filament_cost = 500
filament_density = 1.24
filament_deretraction_speed = nil
filament_diameter = 1.75
filament_flow_ratio = 1.025
filament_is_support = 0
filament_loading_speed = 0
filament_loading_speed_start = 0
filament_long_retractions_when_cut = nil
filament_max_volumetric_speed = 18
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = 
filament_retract_before_wipe = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_lift_enforce = nil
filament_retract_restart_extra = nil
filament_retract_when_changing_layer = nil
filament_retraction_distances_when_cut = nil
filament_retraction_length = nil
filament_retraction_minimum_travel = nil
filament_retraction_speed = nil
filament_shrink = 100%
filament_shrinkage_compensation_z = 100%
filament_soluble = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 0
filament_toolchange_delay = 0
filament_unloading_speed = 0
filament_unloading_speed_start = 0
filament_vendor = Elas
filament_wipe = nil
filament_wipe_distance = nil
filament_z_hop = nil
filament_z_hop_types = nil
full_fan_speed_layer = 0
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
idle_temperature = 0
internal_bridge_fan_speed = -1
ironing_fan_speed = -1
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
overhang_fan_speed = 100
overhang_fan_threshold = 50%
pellet_flow_coefficient = 0.4157
pressure_advance = 0.06
reduce_fan_stop_start_freq = 1
required_nozzle_HRC = 3
slow_down_for_layer_cooling = 1
slow_down_layer_time = 4
slow_down_min_speed = 10
supertack_plate_temp = 45
supertack_plate_temp_initial_layer = 45
support_material_interface_fan_speed = -1
temperature_vitrification = 45
textured_cool_plate_temp = 40
textured_cool_plate_temp_initial_layer = 40
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60

[filament:Elegoo PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFE04
instantiation = false
filament_cost = 0
filament_density = 1.25
filament_max_volumetric_speed = 16
filament_vendor = Elegoo
filament_start_gcode = ; filament start gcode

[filament:Elegoo PLA Matte @base]
inherits = fdm_filament_pla
from = system
filament_id = EPLAMB00
instantiation = false
filament_cost = 0
filament_density = 1.25
filament_vendor = Elegoo
filament_start_gcode = ; filament start gcode

[filament:Elegoo PLA Silk @base]
inherits = fdm_filament_pla
from = system
filament_id = EPLASB00
instantiation = false
filament_cost = 0
filament_density = 1.32
filament_vendor = Elegoo
filament_max_volumetric_speed = 16
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
filament_start_gcode = ; filament start gcode

[filament:Elegoo PLA-CF @base]
inherits = fdm_filament_pla
from = system
filament_id = EPLACFB00
instantiation = false
additional_cooling_fan_speed = 0
cool_plate_temp = 45
cool_plate_temp_initial_layer = 45
filament_type = PLA-CF
filament_vendor = Elegoo
filament_density = 1.21
required_nozzle_HRC = 40
slow_down_layer_time = 7
filament_start_gcode = ; Filament start gcode

filament_end_gcode = ; filament end gcode

[filament:Elegoo Rapid PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFE05
instantiation = false
filament_max_volumetric_speed = 21
filament_density = 1.25
filament_vendor = Elegoo
filament_start_gcode = ; filament start gcode

[filament:Eolas Prints PLA Antibacterial @System]
filament_id = GFSEP008
setting_id = GFSEP008_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 216
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 195
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 30.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PLA High Speed @System]
filament_id = GFSEP005
setting_id = GFSEP005_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 210
nozzle_temperature_range_high = 240
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 17.8

[filament:Eolas Prints PLA INGEO 850 @System]
filament_id = GFSEP006
setting_id = GFSEP006_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 210
nozzle_temperature_initial_layer = 215
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PLA INGEO 870 @System]
filament_id = GFSEP007
setting_id = GFSEP007_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 220
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 235
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.22
filament_cost = 30.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PLA Matte @System]
filament_id = GFSEP002
setting_id = GFSEP002_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 215
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PLA Neon @System]
filament_id = GFSEP004
setting_id = GFSEP004_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 210
nozzle_temperature_initial_layer = 215
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 10

[filament:Eolas Prints PLA Premium @System]
filament_id = GFSEP001
setting_id = GFSEP001_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 210
nozzle_temperature_initial_layer = 215
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 19.90
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:Eolas Prints PLA Silk @System]
filament_id = GFSEP003
setting_id = GFSEP003_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 215
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_low = 205
nozzle_temperature_range_high = 235
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 25.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 8

[filament:Eolas Prints PLA Transition @System]
filament_id = GFSEP009
setting_id = GFSEP009_00
from = system
instantiation = true
inherits = fdm_filament_pla
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = PLA
nozzle_temperature = 210
nozzle_temperature_initial_layer = 215
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 230
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
filament_density = 1.24
filament_cost = 13.90
filament_spool_weight = 1000
filament_max_volumetric_speed = 15

[filament:FDplast PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = FDPLAST04
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 16
filament_density = 1.26
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = FDplast
nozzle_temperature = 215
nozzle_temperature_initial_layer = 215
nozzle_temperature_range_high = 225
nozzle_temperature_range_low = 190
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
textured_plate_temp = 65
textured_plate_temp_initial_layer = 65

[filament:FILL3D PLA Turbo @base]
from = system
filament_id = FILL3D001
instantiation = false
inherits = fdm_filament_pla
adaptive_pressure_advance = 1
adaptive_pressure_advance_model = 0.03,23.43,5000
0.028,25.31,5000
0.025,28.12,5000
0.025,23.43,12000
0.020,25.31,12000
0.018,28.12,12000
additional_cooling_fan_speed = 70
cool_plate_temp = 35
cool_plate_temp_initial_layer = 35
enable_pressure_advance = 1
fan_cooling_layer_time = 100
fan_max_speed = 100
fan_min_speed = 100
filament_cost = 25.4
filament_density = 1.31
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 32
filament_type = PLA
filament_vendor = FILL3D
hot_plate_temp = 55
hot_plate_temp_initial_layer = 55
nozzle_temperature = 235
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
pressure_advance = 0.036
slow_down_layer_time = 4
slow_down_min_speed = 10
supertack_plate_temp = 45
supertack_plate_temp_initial_layer = 45
temperature_vitrification = 45
textured_plate_temp = 55
textured_plate_temp_initial_layer = 55

[filament:Generic PLA @System]
renamed_from = My Generic PLA
inherits = fdm_filament_pla
from = system
setting_id = OGFSA04
instantiation = true
compatible_printers =

[filament:Generic PLA High Speed @System]
inherits = fdm_filament_pla
from = system
setting_id = OGFSL95_00
filament_id = OGFL95
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 18
slow_down_layer_time = 4
compatible_printers =

[filament:Generic PLA Matte @System]
inherits = fdm_filament_pla
from = system
setting_id = OGFSL99_02
instantiation = true
filament_max_volumetric_speed = 11
filament_retraction_length = 0.8
compatible_printers =

[filament:Generic PLA-CF @System]
renamed_from = My Generic PLA-CF
inherits = fdm_filament_pla
from = system
setting_id = OGFSA04
filament_id = OGFL98
instantiation = true
filament_flow_ratio = 0.95
filament_type = PLA-CF
compatible_printers =

[filament:NIT PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = NIT02
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 12
filament_density = 1.26
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = NIT
nozzle_temperature = 210
nozzle_temperature_initial_layer = 210
nozzle_temperature_range_high = 210
nozzle_temperature_range_low = 200

[filament:Numakers PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFNMK00
instantiation = false
filament_cost = 20.99
filament_density = 1.24
filament_flow_ratio = 0.99
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 12
filament_vendor = Numakers
nozzle_temperature = 225
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_high = 255
nozzle_temperature_range_low = 200
filament_scarf_seam_type = none
filament_scarf_height = 10%
filament_scarf_gap = 0%
filament_scarf_length = 10
temperature_vitrification = 55

[filament:Overture Air PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT006
instantiation = false
filament_cost = 27.99
filament_density = 0.82
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 8
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 220
nozzle_temperature_range_low = 190
slow_down_layer_time = 4
temperature_vitrification = 64

[filament:Overture Easy PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT003
instantiation = false
filament_cost = 17.99
filament_density = 1.2
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 220
nozzle_temperature_range_low = 190
slow_down_layer_time = 4
temperature_vitrification = 66

[filament:Overture Matte PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL05
instantiation = false
filament_cost = 24.52
filament_density = 1.22
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Overture
slow_down_layer_time = 6

[filament:Overture PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL04
instantiation = false
filament_cost = 24.15
filament_density = 1.2
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Overture
slow_down_layer_time = 6

[filament:Overture PLA Pro @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT001
instantiation = false
filament_cost = 26.99
filament_density = 1.27
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 220
nozzle_temperature_range_low = 190
slow_down_layer_time = 4
temperature_vitrification = 64

[filament:Overture Rock PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT004
instantiation = false
filament_cost = 24.99
filament_density = 1.3
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 20
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 230
nozzle_temperature_range_low = 190
slow_down_layer_time = 4
temperature_vitrification = 63

[filament:Overture Silk PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT002
instantiation = false
filament_cost = 25.99
filament_density = 1.19
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 220
nozzle_temperature_range_low = 200
slow_down_layer_time = 4
temperature_vitrification = 58

[filament:Overture Super PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = GFOT005
instantiation = false
filament_cost = 28.99
filament_density = 1.21
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 230
nozzle_temperature_range_low = 190
slow_down_layer_time = 4
temperature_vitrification = 63

[filament:Panchroma CoPE @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM016
instantiation = false
filament_cost = 19.99
filament_density = 1.29
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 58

[filament:Panchroma PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM001
instantiation = false
filament_cost = 19.99
filament_density = 1.32
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 58

[filament:Panchroma PLA Celestial @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM008
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Galaxy @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM007
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Glow @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM010
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Luminous @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM011
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Marble @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM003
instantiation = false
filament_cost = 21.99
filament_density = 1.31
filament_flow_ratio = 0.98
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Matte @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM002
instantiation = false
filament_cost = 20.99
filament_density = 1.31
filament_flow_ratio = 0.98
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Metallic @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM012
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Neon @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM013
instantiation = false
filament_cost = 24.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Satin @base]
renamed_from = Panchroma PLA Stain @base
inherits = fdm_filament_pla
from = system
filament_id = OGFPM005
instantiation = false
filament_cost = 20.99
filament_density = 1.24
filament_flow_ratio = 0.95
filament_vendor = Polymaker
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 59

[filament:Panchroma PLA Silk @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM004
instantiation = false
filament_cost = 24.99
filament_density = 1.31
filament_flow_ratio = 0.98
filament_vendor = Polymaker
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 58

[filament:Panchroma PLA Starlight @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM009
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Temp Shift @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM015
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA Translucent @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM006
instantiation = false
filament_cost = 24.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:Panchroma PLA UV Shift @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM014
instantiation = false
filament_cost = 29.99
filament_density = 1.17
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 190
temperature_vitrification = 61

[filament:PolyLite PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL00
instantiation = false
filament_cost = 25.4
filament_flow_ratio = 0.95
filament_vendor = Polymaker

[filament:PolyLite PLA Pro @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM019
instantiation = false
filament_cost = 24.99
filament_density = 1.22
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 220
nozzle_temperature_range_low = 190
temperature_vitrification = 62

[filament:PolyTerra PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL01
instantiation = false
filament_cost = 25.4
filament_density = 1.31
filament_flow_ratio = 0.98
filament_vendor = Polymaker

[filament:Polymaker HT-PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM017
instantiation = false
filament_cost = 26.99
filament_density = 1.28
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 230
nozzle_temperature_range_low = 210
temperature_vitrification = 60
textured_plate_temp = 65
textured_plate_temp_initial_layer = 65

[filament:Polymaker HT-PLA-GF @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFPM018
instantiation = false
filament_cost = 32.99
filament_density = 1.34
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = Polymaker
hot_plate_temp = 65
hot_plate_temp_initial_layer = 65
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 230
nozzle_temperature_range_low = 210
temperature_vitrification = 60
textured_plate_temp = 65
textured_plate_temp_initial_layer = 65

[filament:SUNLU PLA Marble @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL06
instantiation = false
filament_cost = 31.99
filament_density = 1.25
filament_flow_ratio = 0.98
filament_vendor = SUNLU

[filament:SUNLU PLA Matte @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL02
instantiation = false
filament_cost = 25.99
filament_density = 1.3
filament_flow_ratio = 0.98
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
filament_scarf_seam_type = none
filament_scarf_height = 5%
filament_scarf_gap = 0%
filament_scarf_length = 10
temperature_vitrification = 54
nozzle_temperature_range_high = 245
nozzle_temperature_range_low = 205

[filament:SUNLU PLA+ 2.0 @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL04
instantiation = false
filament_cost = 18.99
filament_density = 1.21
filament_flow_ratio = 1.0
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
filament_scarf_seam_type = none
filament_scarf_height = 5%
filament_scarf_gap = 0%
filament_scarf_length = 10
temperature_vitrification = 54

[filament:SUNLU PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL03
instantiation = false
filament_cost = 18.99
filament_density = 1.23
filament_flow_ratio = 1.0
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
filament_scarf_seam_type = none
filament_scarf_height = 5%
filament_scarf_gap = 0%
filament_scarf_length = 10
temperature_vitrification = 54

[filament:SUNLU Silk PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL05
instantiation = false
description = To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.
filament_cost = 29.99
filament_density = 1.25
filament_flow_ratio = 0.98
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
filament_scarf_height = 5%
filament_scarf_gap = 0%
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
supertack_plate_temp = 0
supertack_plate_temp_initial_layer = 0
temperature_vitrification = 54

[filament:SUNLU Wood PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFSNL07
instantiation = false
filament_cost = 26.99
filament_density = 1.10
filament_flow_ratio = 1.0
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_retraction_length = 4
filament_retraction_speed = 50
filament_deretraction_speed = 0
filament_max_volumetric_speed = 12
filament_vendor = SUNLU
filament_scarf_seam_type = none
filament_scarf_height = 5%
filament_scarf_gap = 0%
filament_scarf_length = 10
temperature_vitrification = 54

[filament:Valment PLA @base]
inherits = fdm_filament_pla
from = system
filament_id = VLMNT01
instantiation = false
filament_cost = 670
filament_type = PLA
default_filament_colour = #124943
filament_density = 1.24
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Valment
slow_down_layer_time = 6
nozzle_temperature = 220
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 250
filament_notes = Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz.

Boş Makara Ağırlığı: 150gr
slow_down_min_speed = 20
complete_print_exhaust_fan_speed = 80
during_print_exhaust_fan_speed = 60
additional_cooling_fan_speed = 100

[filament:Valment PLA Galaxy @base]
inherits = fdm_filament_pla
from = system
filament_id = VLMNT04
instantiation = false
filament_cost = 850
filament_type = PLA
default_filament_colour = #124943
filament_density = 1.24
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Valment
slow_down_layer_time = 6
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_low = 220
nozzle_temperature_range_high = 250
filament_notes = Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz.

Galaxy filamentlerimizde; 
0.2mm nozul kullanılmaması,
0.16mm katman yüksekliği altına inilmemesi önerilir.

Boş Makara Ağırlığı: 150gr
slow_down_min_speed = 20
complete_print_exhaust_fan_speed = 80
during_print_exhaust_fan_speed = 60
additional_cooling_fan_speed = 100

[filament:Valment PLA Silk @base]
inherits = fdm_filament_pla
from = system
filament_id = VLMNT02
instantiation = false
filament_cost = 710
filament_type = PLA
filament_density = 1.24
default_filament_colour = #124943
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 7.5
filament_vendor = Valment
slow_down_layer_time = 6
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
nozzle_temperature_range_low = 220
nozzle_temperature_range_high = 250
filament_notes = Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz.

Boş Makara Ağırlığı: 150gr
slow_down_min_speed = 20
complete_print_exhaust_fan_speed = 80
during_print_exhaust_fan_speed = 60
additional_cooling_fan_speed = 100

[filament:Valment PLA-CF @base]
inherits = fdm_filament_pla
from = system
filament_id = VLMNT03
instantiation = false
filament_cost = 1400
filament_type = PLA-CF
default_filament_colour = #124943
filament_density = 1.24
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = Valment
slow_down_layer_time = 6
nozzle_temperature = 225
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_low = 200
nozzle_temperature_range_high = 250
filament_notes = Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz.

Boş Makara Ağırlığı: 150gr
slow_down_min_speed = 20
complete_print_exhaust_fan_speed = 80
during_print_exhaust_fan_speed = 60
additional_cooling_fan_speed = 100

[filament:eSUN PLA+ @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL03
instantiation = false
filament_cost = 22.99
filament_density = 1.25
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 12
filament_vendor = eSUN
slow_down_layer_time = 6

[filament:eSUN PLA-Basic @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL04
instantiation = false
filament_cost = 11.99
filament_density = 1.24
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16
filament_vendor = eSUN
slow_down_layer_time = 6

[filament:eSUN PLA-Marble @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL06
instantiation = false
filament_cost = 28.99
filament_density = 1.27
filament_flow_ratio = 0.99
filament_max_volumetric_speed = 8
filament_vendor = eSUN
slow_down_layer_time = 6

[filament:eSUN PLA-Matte @base]
inherits = fdm_filament_pla
from = system
filament_id = OGFL05
instantiation = false
filament_cost = 14.99
filament_density = 1.32
filament_flow_ratio = 0.99
filament_max_volumetric_speed = 8
filament_vendor = eSUN
slow_down_layer_time = 6

[filament:eSUN ePLA-LW @System]
inherits = fdm_filament_pla
from = system
setting_id = LWSL02_00
filament_id = ESN02
instantiation = true
filament_type = PLA-AERO
filament_cost = 33.99
filament_density = 1.2
filament_flow_ratio = 0.48
filament_max_volumetric_speed = 6
filament_vendor = eSUN
filament_scarf_seam_type = none
nozzle_temperature = 243
nozzle_temperature_initial_layer = 243
nozzle_temperature_range_low = 190
nozzle_temperature_range_high = 270
temperature_vitrification = 53
compatible_printers =

[filament:fdm_filament_pla_silk]
inherits = fdm_filament_pla
from = system
filament_id = OGFL96
instantiation = false
description = To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.
filament_flow_ratio = 0.98
slow_down_layer_time = 8

[filament:Generic PP @System]
inherits = fdm_filament_pp
from = system
setting_id = OGFSP97_00
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
compatible_printers =

[filament:Generic PP-CF @System]
inherits = fdm_filament_pp
from = system
setting_id = OGFSP96_00
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
filament_cost = 77.99
filament_density = 1.01
filament_max_volumetric_speed = 6
filament_type = PP-CF
compatible_printers =

[filament:Generic PP-GF @System]
inherits = fdm_filament_pp
from = system
setting_id = OGFSP97_03
instantiation = true
description = This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
filament_cost = 59.99
filament_density = 1.05
filament_max_volumetric_speed = 6
filament_type = PP-GF
compatible_printers =

[filament:Bambu PPA-CF @base]
inherits = fdm_filament_ppa
from = system
filament_id = OGFN06
instantiation = false
filament_vendor = Bambu Lab
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.

[filament:Generic PPA-CF @System]
inherits = fdm_filament_ppa
from = system
setting_id = OGFSN97_00
instantiation = true
fan_max_speed = 35
filament_max_volumetric_speed = 6.5
overhang_fan_threshold = 25%
filament_type = PPA-CF
compatible_printers =

[filament:Generic PPA-GF @System]
inherits = fdm_filament_ppa
from = system
setting_id = OGFSN96_00
filament_id = OGFN96
instantiation = true
filament_max_volumetric_speed = 6
filament_type = PPA-GF
compatible_printers =

[filament:Bambu PPS-CF @base]
inherits = fdm_filament_pps
from = system
filament_id = OGFT02
instantiation = false
description = When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
fan_max_speed = 30
filament_cost = 175
filament_density = 1.26
filament_max_volumetric_speed = 6
filament_type = PPS-CF
filament_vendor = Bambu Lab
nozzle_temperature_range_low = 310
overhang_fan_threshold = 25%
required_nozzle_HRC = 40
temperature_vitrification = 220

[filament:Bambu PVA @base]
inherits = fdm_filament_pva
from = system
filament_id = OGFS04
instantiation = false
description = This is a water-soluble support filament, and usually it is only for the support structure and not for the model body. Printing this filament is of many requirements, and to get better printing quality, please refer to this wiki: PVA Printing Guide.
filament_cost = 79.98
filament_density = 1.27
filament_max_volumetric_speed = 6
filament_vendor = Bambu Lab
nozzle_temperature_range_high = 250
nozzle_temperature_range_low = 210
slow_down_layer_time = 7
slow_down_min_speed = 20

[filament:Generic PVA @System]
renamed_from = My Generic PVA
inherits = fdm_filament_pva
from = system
setting_id = OGFSA04
filament_id = OGFS99
instantiation = true
compatible_printers =

[filament:FDplast SBS @base]
inherits = fdm_filament_sbs
from = system
filament_id = FDPLAST05
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 27
filament_density = 1.26
filament_flow_ratio = 0.98
filament_vendor = FDplast
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_high = 240
nozzle_temperature_range_low = 225
hot_plate_temp = 80
hot_plate_temp_initial_layer = 80
textured_plate_temp = 80
textured_plate_temp_initial_layer = 80

[filament:Generic SBS @System]
inherits = fdm_filament_sbs
from = system
setting_id = OGFSL99
instantiation = true
compatible_printers =

[filament:Bambu TPU 95A @base]
inherits = fdm_filament_tpu
from = system
filament_id = OGFU01
instantiation = false
description = This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide.
filament_cost = 41.99
filament_density = 1.22
filament_vendor = Bambu Lab
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230

[filament:Bambu TPU 95A HF @base]
inherits = fdm_filament_tpu
from = system
filament_id = OGFU00
instantiation = false
description = This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide.
filament_cost = 41.99
filament_density = 1.22
filament_max_volumetric_speed = 12
filament_retraction_length = 0.8
filament_vendor = Bambu Lab
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230

[filament:COEX TPE 30D @base]
inherits = fdm_filament_tpu
from = system
filament_id = CX30DB20
instantiation = false
filament_vendor = COEX 3D
filament_cost = 80.00
filament_density = 1.15
filament_type = TPU
filament_notes = Flexible filament - print slowly with minimal retraction
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
bed_temperature = 30
bed_temperature_initial_layer = 35
temperature_vitrification = 60
filament_max_volumetric_speed = 3.5
filament_retraction_minimum_travel = 3
filament_retract_before_wipe = 0%
filament_retract_layer_change = 0
filament_retract_when_changing_layer = 0
filament_retraction_length = 0.4
filament_retraction_speed = 20
filament_deretraction_speed = 20
filament_wipe = 0
filament_wipe_distance = 0
fan_min_speed = 80
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 2
slow_down_layer_time = 10
slow_down_min_speed = 5
enable_pressure_advance = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX TPE 40D @base]
inherits = fdm_filament_tpu
from = system
filament_id = CX40DB20
instantiation = false
filament_vendor = COEX 3D
filament_cost = 80.00
filament_density = 1.18
filament_type = TPU
filament_notes = Flexible filament - print slowly with minimal retraction
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
bed_temperature = 30
bed_temperature_initial_layer = 35
temperature_vitrification = 60
filament_max_volumetric_speed = 5.5
filament_retraction_minimum_travel = 3
filament_retract_before_wipe = 0%
filament_retract_layer_change = 0
filament_retract_when_changing_layer = 0
filament_retraction_length = 0.4
filament_retraction_speed = 20
filament_deretraction_speed = 20
filament_wipe = 0
filament_wipe_distance = 0
fan_min_speed = 80
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 2
slow_down_layer_time = 10
slow_down_min_speed = 5
enable_pressure_advance = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX TPE 60D @base]
inherits = fdm_filament_tpu
from = system
filament_id = CX60DB19
instantiation = false
filament_vendor = COEX 3D
filament_cost = 80.00
filament_density = 1.20
filament_type = TPU
filament_notes = Flexible filament - print slowly with minimal retraction
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
bed_temperature = 30
bed_temperature_initial_layer = 35
temperature_vitrification = 60
filament_max_volumetric_speed = 6.5
filament_retraction_minimum_travel = 3
filament_retract_before_wipe = 0%
filament_retract_layer_change = 0
filament_retract_when_changing_layer = 0
filament_retraction_length = 0.4
filament_retraction_speed = 20
filament_deretraction_speed = 20
filament_wipe = 0
filament_wipe_distance = 0
fan_min_speed = 80
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 2
slow_down_layer_time = 10
slow_down_min_speed = 5
enable_pressure_advance = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:COEX TPU 60A @base]
inherits = fdm_filament_tpu
from = system
filament_id = CX60AB17
instantiation = false
filament_vendor = COEX 3D
filament_cost = 95.00
filament_density = 1.14
filament_type = TPU
filament_notes = Flexible filament - print slowly with minimal retraction
nozzle_temperature = 225
nozzle_temperature_initial_layer = 225
bed_temperature = 0
bed_temperature_initial_layer = 0
temperature_vitrification = 60
filament_max_volumetric_speed = 1
filament_retraction_minimum_travel = 3
filament_retract_before_wipe = 0%
filament_retract_layer_change = 0
filament_retract_when_changing_layer = 0
filament_retraction_length = 0
filament_retraction_speed = 20
filament_deretraction_speed = 20
filament_wipe = 0
filament_wipe_distance = 0
fan_min_speed = 80
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 2
slow_down_layer_time = 10
slow_down_min_speed = 5
enable_pressure_advance = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Elegoo TPU 95A @base]
inherits = fdm_filament_tpu
from = system
filament_id = OGFE07
instantiation = false
filament_max_volumetric_speed = 3.6
filament_vendor = Elegoo
filament_density = 1.21
nozzle_temperature = 225
nozzle_temperature_initial_layer = 225
filament_start_gcode = ; filament start gcode

[filament:Elegoo TPU @base]
inherits = fdm_filament_tpu
from = system
filament_id = ETPUB00
instantiation = false
filament_max_volumetric_speed = 3.6
filament_vendor = Elegoo
filament_density = 1.21
nozzle_temperature = 225
nozzle_temperature_initial_layer = 225
filament_start_gcode = ; filament start gcode

[filament:Eolas Prints TPU D60 UV Resistant @System]
filament_id = GFSEP015
setting_id = GFSEP015_00
from = system
instantiation = true
inherits = fdm_filament_tpu
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = TPU
nozzle_temperature = 225
nozzle_temperature_initial_layer = 230
nozzle_temperature_range_low = 215
nozzle_temperature_range_high = 245
hot_plate_temp = 55
hot_plate_temp_initial_layer = 60
filament_density = 1.16
filament_cost = 37.90
filament_spool_weight = 1000
filament_max_volumetric_speed = 8

[filament:Eolas Prints TPU Flex 93A @System]
filament_id = GFSEP013
setting_id = GFSEP013_00
from = system
instantiation = true
inherits = fdm_filament_tpu
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = TPU
nozzle_temperature = 220
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_low = 210
nozzle_temperature_range_high = 240
hot_plate_temp = 50
hot_plate_temp_initial_layer = 55
filament_density = 1.21
filament_cost = 34.99
filament_spool_weight = 1000
filament_max_volumetric_speed = 6

[filament:Eolas Prints TPU Flex D53 @System]
filament_id = GFSEP014
setting_id = GFSEP014_00
from = system
instantiation = true
inherits = fdm_filament_tpu
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = TPU
nozzle_temperature = 220
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_low = 205
nozzle_temperature_range_high = 235
hot_plate_temp = 45
hot_plate_temp_initial_layer = 50
filament_density = 1.17
filament_cost = 38.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 8

[filament:Eolas Prints TPU Transition @System]
filament_id = GFSEP016
setting_id = GFSEP016_00
from = system
instantiation = true
inherits = fdm_filament_tpu
filament_color = #4d9398
filament_vendor = Eolas Prints
filament_type = TPU
nozzle_temperature = 220
nozzle_temperature_initial_layer = 225
nozzle_temperature_range_low = 210
nozzle_temperature_range_high = 240
hot_plate_temp = 50
hot_plate_temp_initial_layer = 55
filament_density = 1.21
filament_cost = 22.50
filament_spool_weight = 1000
filament_max_volumetric_speed = 5

[filament:FDplast TPU @base]
inherits = fdm_filament_tpu
from = system
filament_id = FDPLAST06
instantiation = false
description = When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.
filament_cost = 27
filament_density = 1.26
filament_flow_ratio = 0.98
filament_vendor = FDplast
nozzle_temperature = 180
nozzle_temperature_initial_layer = 180
nozzle_temperature_range_high = 190
nozzle_temperature_range_low = 175
hot_plate_temp = 60
hot_plate_temp_initial_layer = 60
textured_plate_temp = 60
textured_plate_temp_initial_layer = 60

[filament:Generic TPU @System]
renamed_from = My Generic TPU
inherits = fdm_filament_tpu
from = system
setting_id = OGFSA04
filament_id = OGFU99
instantiation = true
compatible_printers =

[filament:Overture TPU @base]
inherits = fdm_filament_tpu
from = system
filament_id = GFOT008
instantiation = false
fan_cooling_layer_time = 100
fan_max_speed = 100
fan_min_speed = 100
filament_cost = 29.99
filament_density = 1.18
filament_flow_ratio = 1
filament_max_volumetric_speed = 10
filament_vendor = Overture
nozzle_temperature = 220
nozzle_temperature_initial_layer = 220
nozzle_temperature_range_high = 230
nozzle_temperature_range_low = 210
slow_down_layer_time = 15
temperature_vitrification = 30

[filament:Bambu ABS @System]
inherits = Bambu ABS @base
from = system
setting_id = OGFSB00
instantiation = true
fan_max_speed = 60
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 16
filament_retraction_distances_when_cut = 18
slow_down_layer_time = 12
compatible_printers =

[filament:Bambu ABS-GF @System]
inherits = Bambu ABS-GF @base
from = system
setting_id = OGFSB50_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu Support for ABS @System]
inherits = Bambu Support for ABS @base
from = system
setting_id = OGFSS06_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:COEX ABS @System]
inherits = COEX ABS @base
from = system
setting_id = COXABS01
instantiation = true
filament_max_volumetric_speed = 16
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:COEX ABS PRIME @System]
inherits = COEX ABS PRIME @base
from = system
setting_id = CXABSP09
instantiation = true
filament_max_volumetric_speed = 16
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:FDplast ABS @System]
inherits = FDplast ABS @base
from = system
setting_id = ABS01_00
instantiation = true
compatible_printers =

[filament:NIT ABS @System]
inherits = NIT ABS @base
from = system
setting_id = ABS01_00
instantiation = true
compatible_printers =

[filament:Overture ABS Basic @System]
inherits = Overture ABS Basic @base
from = system
setting_id = OVABS08
instantiation = true
filament_max_volumetric_speed = 16
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:PolyLite ABS @System]
inherits = PolyLite ABS @base
from = system
setting_id = OGFSB60_00
instantiation = true
compatible_printers =

[filament:Bambu ASA @System]
inherits = Bambu ASA @base
from = system
setting_id = OGFSB01_00
instantiation = true
fan_min_speed = 25
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu ASA-Aero @System]
inherits = Bambu ASA-Aero @base
from = system
setting_id = OGFSB02_00
instantiation = true
compatible_printers =

[filament:Bambu ASA-CF @System]
inherits = Bambu ASA-CF @base
from = system
setting_id = OGFSB51_00
instantiation = true
compatible_printers =

[filament:COEX ASA PRIME @System]
inherits = COEX ASA PRIME @base
from = system
setting_id = CXASAP04
instantiation = true
filament_max_volumetric_speed = 16
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:Elas ASA @System]
inherits = Elas ASA @base
from = system
setting_id = OGFSB01_00
instantiation = true
fan_min_speed = 25
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Elegoo ASA @System]
inherits = Elegoo ASA @base
from = system
setting_id = OGFSE06_00
instantiation = true
compatible_printers =

[filament:Overture ASA @System]
inherits = Overture ASA @base
from = system
setting_id = OGFOT009
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 8

[filament:PolyLite ASA @System]
inherits = PolyLite ASA @base
from = system
setting_id = OGFSB61_00
instantiation = true
compatible_printers =

[filament:FDplast HIPS @System]
inherits = FDplast HIPS @base
from = system
setting_id = HIPS01_00
instantiation = true
compatible_printers =

[filament:AliZ PA-CF @System]
inherits = AliZ PA-CF @base
from = system
setting_id = AliZGFSA04
instantiation = true
compatible_printers =

[filament:Bambu PA-CF @System]
inherits = Bambu PA-CF @base
from = system
setting_id = OGFSN00
instantiation = true
nozzle_temperature_initial_layer = 290
nozzle_temperature = 290
fan_max_speed = 30
fan_min_speed = 10
fan_cooling_layer_time = 5
full_fan_speed_layer = 2
compatible_printers =

[filament:Bambu PA6-CF @System]
inherits = Bambu PA6-CF @base
from = system
setting_id = OGFSN05_02
instantiation = true
compatible_printers =

[filament:Bambu PA6-GF @System]
inherits = Bambu PA6-GF @base
from = system
setting_id = OGFSN08_00
instantiation = true
chamber_temperatures = 60
filament_max_volumetric_speed = 10.5
nozzle_temperature = 265
nozzle_temperature_initial_layer = 265
compatible_printers =

[filament:Bambu PAHT-CF @System]
inherits = Bambu PAHT-CF @base
from = system
setting_id = OGFSN04
instantiation = true
chamber_temperatures = 60
compatible_printers =

[filament:Bambu Support For PA/PET @System]
inherits = Bambu Support For PA/PET @base
from = system
setting_id = OGFSS03_00
instantiation = true
chamber_temperatures = 60
compatible_printers =

[filament:Bambu Support G @System]
inherits = Bambu Support G @base
from = system
setting_id = OGFSS01
instantiation = true
compatible_printers =

[filament:COEX NYLEX PA6-CF @System]
inherits = COEX NYLEX PA6-CF @base
from = system
setting_id = CXPACF23
instantiation = true
filament_max_volumetric_speed = 11
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:Fiberon PA12-CF @System]
inherits = Fiberon PA12-CF @base
from = system
setting_id = OGFSL52_00
instantiation = true
compatible_printers =

[filament:Fiberon PA6-CF @System]
inherits = Fiberon PA6-CF @base
from = system
setting_id = OGFSL50_00
instantiation = true
compatible_printers =

[filament:Fiberon PA6-GF @System]
inherits = Fiberon PA6-GF @base
from = system
setting_id = OGFSL51_00
instantiation = true
compatible_printers =

[filament:Fiberon PA612-CF @System]
inherits = Fiberon PA612-CF @base
from = system
setting_id = OGFSL53_00
instantiation = true
compatible_printers =

[filament:Bambu PC @System]
inherits = Bambu PC @base
from = system
setting_id = OGFSC00
instantiation = true
fan_max_speed = 40
slow_down_layer_time = 12
compatible_printers =

[filament:Bambu PC FR @System]
inherits = Bambu PC FR @base
from = system
setting_id = OGFSC01_00
instantiation = true
fan_max_speed = 40
slow_down_layer_time = 12
compatible_printers =

[filament:COEX PCTG PRIME @System]
inherits = COEX PCTG PRIME @base
from = system
setting_id = CXPCTG15
instantiation = true
filament_max_volumetric_speed = 12
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:AliZ PETG @System]
inherits = AliZ PETG @base
from = system
setting_id = AliZGFSA04
instantiation = true
compatible_printers =

[filament:AliZ PETG-CF @base]
inherits = AliZ PETG @base
from = system
filament_id = AZ01-1
instantiation = false
fan_cooling_layer_time = 30
overhang_fan_speed = 100
close_fan_the_first_x_layers = 2
enable_pressure_advance = 0
pressure_advance = 0.033
fan_max_speed = 35
fan_min_speed = 10
filament_cost = 49.9
filament_flow_ratio = 1
filament_max_volumetric_speed = 10
filament_type = PETG-CF
filament_vendor = Aliz
hot_plate_temp = 79
hot_plate_temp_initial_layer = 79
nozzle_temperature = 275
nozzle_temperature_initial_layer = 275
nozzle_temperature_range_high = 290
nozzle_temperature_range_low = 260
overhang_fan_threshold = 25%
slow_down_min_speed = 10
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:AliZ PETG-Metal @base]
inherits = AliZ PETG @base
from = system
filament_id = AZ01-2
instantiation = false
fan_cooling_layer_time = 30
overhang_fan_speed = 100
close_fan_the_first_x_layers = 2
enable_pressure_advance = 0
fan_max_speed = 80
fan_min_speed = 30
filament_cost = 49.9
filament_flow_ratio = 1
filament_max_volumetric_speed = 13
filament_vendor = Aliz
hot_plate_temp = 79
hot_plate_temp_initial_layer = 79
nozzle_temperature = 260
nozzle_temperature_initial_layer = 260
overhang_fan_threshold = 25%
pressure_advance = 0.036
slow_down_min_speed = 10
textured_plate_temp = 70
textured_plate_temp_initial_layer = 70

[filament:Bambu PET-CF @System]
inherits = Bambu PET-CF @base
from = system
setting_id = OGFST01
instantiation = true
reduce_fan_stop_start_freq = 0
slow_down_min_speed = 10
compatible_printers =

[filament:Bambu PETG Basic @System]
inherits = Bambu PETG Basic @base
from = system
setting_id = OGFSG00_01
instantiation = true
filament_max_volumetric_speed = 13
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PETG HF @System]
inherits = Bambu PETG HF @base
from = system
setting_id = OGFSG02_00
instantiation = true
fan_cooling_layer_time = 20
fan_min_speed = 20
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
overhang_fan_speed = 100
slow_down_layer_time = 10
slow_down_min_speed = 10
compatible_printers =

[filament:Bambu PETG Translucent @System]
inherits = Bambu PETG Translucent @base
from = system
setting_id = OGFSG01_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_retraction_length = 0.3
slow_down_layer_time = 8
compatible_printers =

[filament:Bambu PETG-CF @System]
inherits = Bambu PETG-CF @base
from = system
setting_id = OGFSG50_01
instantiation = true
fan_cooling_layer_time = 30
fan_max_speed = 40
fan_min_speed = 5
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 11.5
filament_retraction_distances_when_cut = 18
overhang_fan_speed = 100
compatible_printers =

[filament:COEX PETG @System]
inherits = COEX PETG @base
from = system
setting_id = CXPETG13
instantiation = true
filament_max_volumetric_speed = 16
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:Elas PETG Basic @System]
inherits = Elas PETG Basic @base
from = system
setting_id = OGFSG00_01
instantiation = true
filament_max_volumetric_speed = 13
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Elegoo PETG PRO @System]
renamed_from = Elegoo PETG Pro @System
inherits = Elegoo PETG PRO @base
from = system
setting_id = OGFSE02_00
instantiation = true
compatible_printers =

[filament:Elegoo PETG-CF @System]
inherits = Elegoo PETG-CF @base
from = system
setting_id = OGFSE03_00
instantiation = true
compatible_printers =

[filament:Elegoo Rapid PETG @System]
inherits = Elegoo Rapid PETG @base
from = system
setting_id = OGFSE01_00
instantiation = true
compatible_printers =

[filament:FDplast PETG @System]
inherits = FDplast PETG @base
from = system
setting_id = PET01_00
instantiation = true
compatible_printers =

[filament:Fiberon PET-CF @System]
inherits = Fiberon PET-CF @base
from = system
setting_id = OGFSL54_00
instantiation = true
compatible_printers =

[filament:Fiberon PETG-ESD @System]
inherits = Fiberon PETG-ESD @base
from = system
setting_id = OGFSL06_00
instantiation = true
filament_cost = 29.99
compatible_printers =

[filament:Fiberon PETG-rCF @System]
inherits = Fiberon PETG-rCF @base
from = system
setting_id = OGFSL55_00
instantiation = true
compatible_printers =

[filament:NIT PETG @System]
inherits = NIT PETG @base
from = system
setting_id = PET01_00
instantiation = true
compatible_printers =

[filament:PolyLite PETG @System]
inherits = PolyLite PETG @base
from = system
setting_id = OGFSG60_00
instantiation = true
filament_max_volumetric_speed = 11.5
nozzle_temperature_range_high = 270
compatible_printers =

[filament:SUNLU PETG @System]
inherits = SUNLU PETG @base
from = system
setting_id = OSNLS08
instantiation = true
filament_max_volumetric_speed = 14
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:eSUN PETG @System]
inherits = eSUN PETG @base
from = system
setting_id = PET01_00
instantiation = true
compatible_printers =

[filament:AliZ PLA @System]
inherits = AliZ PLA @base
from = system
setting_id = AliZGFSA04
instantiation = true
compatible_printers =

[filament:Bambu PLA Aero @System]
inherits = Bambu PLA Aero @base
from = system
setting_id = OGFSA11_01
instantiation = true
additional_cooling_fan_speed = 0
slow_down_layer_time = 8
compatible_printers =

[filament:Bambu PLA Basic @System]
inherits = Bambu PLA Basic @base
from = system
setting_id = OGFSA00
instantiation = true
filament_max_volumetric_speed = 21
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PLA Dynamic @System]
inherits = Bambu PLA Dynamic @base
from = system
setting_id = OGFSA13_00
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 21
filament_vendor = Bambu Lab
compatible_printers =

[filament:Bambu PLA Galaxy @System]
inherits = Bambu PLA Galaxy @base
from = system
setting_id = OGFSA15_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PLA Glow @System]
inherits = Bambu PLA Glow @base
from = system
setting_id = OGFSA12_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PLA Impact @System]
inherits = Bambu PLA Impact @base
from = system
setting_id = OGFSA03
instantiation = true
filament_max_volumetric_speed = 23.2
compatible_printers =

[filament:Bambu PLA Marble @System]
inherits = Bambu PLA Marble @base
from = system
setting_id = OGFSA07_00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PLA Matte @System]
inherits = Bambu PLA Matte @base
from = system
setting_id = OGFSA01
instantiation = true
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 22
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu PLA Metal @System]
inherits = Bambu PLA Metal @base
from = system
setting_id = OGFSA02
instantiation = true
filament_max_volumetric_speed = 21
compatible_printers =

[filament:Bambu PLA Silk @System]
inherits = Bambu PLA Silk @base
from = system
setting_id = OGFSA05_01
instantiation = true
compatible_printers =

[filament:Bambu PLA Silk+ @System]
inherits = Bambu PLA Silk+ @base
from = system
setting_id = OGFSA06_00
instantiation = true
supertack_plate_temp = 35
supertack_plate_temp_initial_layer = 35
compatible_printers =

[filament:Bambu PLA Sparkle @System]
inherits = Bambu PLA Sparkle @base
from = system
setting_id = OGFSA08_00
instantiation = true
compatible_printers =

[filament:Bambu PLA Tough @System]
inherits = Bambu PLA Tough @base
from = system
setting_id = OGFSA09_02
instantiation = true
filament_max_volumetric_speed = 21
compatible_printers =

[filament:Bambu PLA Wood @System]
inherits = Bambu PLA Wood @base
from = system
setting_id = OGFSA16_00
instantiation = true
compatible_printers =

[filament:Bambu PLA-CF @System]
inherits = Bambu PLA-CF @base
from = system
setting_id = OGFSA50_01
instantiation = true
filament_long_retractions_when_cut = 1
filament_max_volumetric_speed = 15
filament_retraction_distances_when_cut = 18
nozzle_temperature = 230
nozzle_temperature_initial_layer = 230
compatible_printers =

[filament:Bambu Support For PLA @System]
inherits = Bambu Support For PLA @base
from = system
setting_id = OGFSS02_02
instantiation = true
compatible_printers =

[filament:Bambu Support For PLA/PETG @System]
inherits = Bambu Support For PLA/PETG @base
from = system
setting_id = OGFSS05_00
instantiation = true
eng_plate_temp = 60
eng_plate_temp_initial_layer = 60
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Bambu Support W @System]
inherits = Bambu Support W @base
from = system
setting_id = OGFSS00
instantiation = true
compatible_printers =

[filament:COEX PLA @System]
inherits = COEX PLA @base
from = system
setting_id = C0XPLA02
instantiation = true
filament_max_volumetric_speed = 18
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:COEX PLA PRIME @System]
inherits = COEX PLA PRIME @base
from = system
setting_id = C0XPLA08
instantiation = true
filament_max_volumetric_speed = 15
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:Elas PLA Basic @System]
inherits = Elas PLA Basic @base
from = system
setting_id = OGFSA00
instantiation = true
filament_max_volumetric_speed = 13
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Elas PLA Pro @System]
inherits = Elas PLA Pro @base
from = system
setting_id = OGFSA00
instantiation = true
filament_max_volumetric_speed = 13
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:Elegoo PLA @System]
inherits = Elegoo PLA @base
from = system
setting_id = OGFSE04_00
instantiation = true
compatible_printers =

[filament:Elegoo Rapid PLA+ @System]
inherits = Elegoo Rapid PLA+ @base
from = system
setting_id = OGFSE05_00
instantiation = true
compatible_printers =

[filament:FDplast PLA @System]
inherits = FDplast PLA @base
from = system
setting_id = PLA01_00
instantiation = true
compatible_printers =

[filament:FILL3D PLA Turbo @System]
setting_id = FILL3D001SYS
from = system
instantiation = true
inherits = FILL3D PLA Turbo @base
compatible_printers =

[filament:NIT PLA @System]
inherits = NIT PLA @base
from = system
setting_id = PLA01_00
instantiation = true
compatible_printers =

[filament:Numakers PLA+ @System]
inherits = Numakers PLA+ @base
from = system
setting_id = ONMK00
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
filament_max_volumetric_speed = 18
compatible_printers =

[filament:Overture Air PLA @System]
inherits = Overture Air PLA @base
from = system
setting_id = OGFOT006
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Overture Easy PLA @System]
inherits = Overture Easy PLA @base
from = system
setting_id = OGFOT003
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Overture Matte PLA @System]
inherits = Overture Matte PLA @base
from = system
setting_id = OGFSL05_00
instantiation = true
compatible_printers =

[filament:Overture PLA @System]
inherits = Overture PLA @base
from = system
setting_id = OGFSL04_05
instantiation = true
compatible_printers =

[filament:Overture PLA Pro @System]
inherits = Overture PLA Pro @base
from = system
setting_id = OGFOT001
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Overture Rock PLA @System]
inherits = Overture Rock PLA @base
from = system
setting_id = OGFOT004
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Overture Silk PLA @System]
inherits = Overture Silk PLA @base
from = system
setting_id = OGFOT002
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Overture Super PLA+ @System]
inherits = Overture Super PLA+ @base
from = system
setting_id = OGFOT005
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Panchroma CoPE @System]
inherits = Panchroma CoPE @base
from = system
setting_id = OGFSPM016
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA @System]
inherits = Panchroma PLA @base
from = system
setting_id = OGFSPM001
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Celestial @System]
inherits = Panchroma PLA Celestial @base
from = system
setting_id = OGFSPM008
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Galaxy @System]
inherits = Panchroma PLA Galaxy @base
from = system
setting_id = OGFSPM007
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Glow @System]
inherits = Panchroma PLA Glow @base
from = system
setting_id = OGFSPM010
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Luminous @System]
inherits = Panchroma PLA Luminous @base
from = system
setting_id = OGFSPM011
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Marble @System]
inherits = Panchroma PLA Marble @base
from = system
setting_id = OGFSPM003
instantiation = true
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Matte @System]
inherits = Panchroma PLA Matte @base
from = system
setting_id = GFSPM002
instantiation = true
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Metallic @System]
inherits = Panchroma PLA Metallic @base
from = system
setting_id = OGFSPM012
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Neon @System]
inherits = Panchroma PLA Neon @base
from = system
setting_id = OGFSPM013
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Satin @System]
renamed_from = Panchroma PLA Stain @System
inherits = Panchroma PLA Satin @base
from = system
setting_id = OGFSPM005
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Silk @System]
inherits = Panchroma PLA Silk @base
from = system
setting_id = OGFSPM004
instantiation = true
filament_flow_ratio = 0.98

[filament:Panchroma PLA Starlight @System]
inherits = Panchroma PLA Starlight @base
from = system
setting_id = OGFSPM009
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Temp Shift @System]
inherits = Panchroma PLA Temp Shift @base
from = system
setting_id = OGFSPM015
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA Translucent @System]
inherits = Panchroma PLA Translucent @base
from = system
setting_id = OGFSPM006
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Panchroma PLA UV Shift @System]
inherits = Panchroma PLA UV Shift @base
from = system
setting_id = OGFSPM014
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:PolyLite Dual PLA @System]
renamed_from = PolyLite Dual PLA
inherits = PolyLite PLA @base
from = system
setting_id = O64868365
instantiation = true
compatible_printers =

[filament:PolyLite PLA @System]
inherits = PolyLite PLA @base
from = system
setting_id = OGFSL19
filament_id = OGFL00
instantiation = true
filament_max_volumetric_speed = 15
compatible_printers =

[filament:PolyLite PLA Pro @System]
inherits = PolyLite PLA Pro @base
from = system
setting_id = OGFSPM019
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 16

[filament:PolyTerra Dual PLA @System]
renamed_from = PolyTerra Dual PLA
inherits = PolyTerra PLA @base
from = system
setting_id = O1258005940
filament_id = OGFL00-1
instantiation = true
compatible_printers =

[filament:PolyTerra PLA @System]
renamed_from = PolyTerra PLA
inherits = PolyTerra PLA @base
from = system
setting_id = OGFSL18
instantiation = true
filament_max_volumetric_speed = 22
compatible_printers =

[filament:Polymaker HT-PLA @System]
inherits = Polymaker HT-PLA @base
from = system
setting_id = OGFSPM017
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:Polymaker HT-PLA-GF @System]
inherits = Polymaker HT-PLA-GF @base
from = system
setting_id = OGFSPM018
instantiation = true
filament_flow_ratio = 0.98
filament_max_volumetric_speed = 16

[filament:SUNLU PLA Marble @System]
inherits = SUNLU PLA Marble @base
from = system
setting_id = OSNLS06
instantiation = true
filament_long_retractions_when_cut = 1
filament_retraction_distances_when_cut = 18
compatible_printers =

[filament:SUNLU PLA Matte @System]
inherits = SUNLU PLA Matte @base
from = system
setting_id = OSNLS02
instantiation = true
compatible_printers =

[filament:SUNLU PLA+ 2.0 @System]
inherits = SUNLU PLA+ 2.0 @base
from = system
setting_id = OSNLS04
instantiation = true
compatible_printers =

[filament:SUNLU PLA+ @System]
inherits = SUNLU PLA+ @base
from = system
setting_id = OSNLS03
instantiation = true
compatible_printers =

[filament:SUNLU Silk PLA+ @System]
inherits = SUNLU Silk PLA+ @base
from = system
setting_id = OSNLS05
instantiation = true
compatible_printers =

[filament:SUNLU Wood PLA @System]
inherits = SUNLU Wood PLA @base
from = system
setting_id = OSNLS07
instantiation = true
compatible_printers =

[filament:Valment PLA @System]
inherits = Valment PLA @base
from = system
setting_id = VLMNT_01
instantiation = true
compatible_printers =

[filament:Valment PLA Galaxy @System]
inherits = Valment PLA Galaxy @base
from = system
setting_id = VLMNT_04
instantiation = true
compatible_printers =

[filament:Valment PLA Silk @System]
inherits = Valment PLA Silk @base
from = system
setting_id = VLMNT_02
instantiation = true
compatible_printers =

[filament:Valment PLA-CF @System]
inherits = Valment PLA-CF @base
from = system
setting_id = VLMNT_03
instantiation = true
compatible_printers =

[filament:eSUN PLA+ @System]
inherits = eSUN PLA+ @base
from = system
setting_id = OGFSL03_00
instantiation = true
compatible_printers =

[filament:eSUN PLA-Basic @System]
inherits = eSUN PLA-Basic @base
from = system
setting_id = OGFSL04_00
instantiation = true
compatible_printers =

[filament:eSUN PLA-Marble @System]
inherits = eSUN PLA-Marble @base
from = system
setting_id = OGFSL06_00
instantiation = true
compatible_printers =

[filament:eSUN PLA-Matte @System]
inherits = eSUN PLA-Matte @base
from = system
setting_id = OGFSL05_00
instantiation = true
compatible_printers =

[filament:COEX PLA+Silk @base]
inherits = fdm_filament_pla_silk
from = system
filament_id = CXPLSB03
instantiation = false
filament_vendor = COEX 3D
filament_cost = 30.00
filament_density = 1.24
filament_type = PLA
filament_notes = Silk finish for aesthetic prints - slightly higher temperature than regular PLA
nozzle_temperature = 240
nozzle_temperature_initial_layer = 245
bed_temperature = 60
bed_temperature_initial_layer = 60
temperature_vitrification = 55
filament_max_volumetric_speed = 15
filament_retraction_minimum_travel = 2
filament_retract_before_wipe = 70%
filament_retract_layer_change = 1
filament_retract_when_changing_layer = 1
filament_retraction_length = 1.5
filament_retraction_speed = 45
filament_deretraction_speed = 40
filament_wipe = 1
filament_wipe_distance = 2
fan_min_speed = 100
fan_max_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slow_down_layer_time = 5
slow_down_min_speed = 10
external_perimeter_speed = 50%
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition =

[filament:Generic PLA Silk @System]
renamed_from = Generic Silk PLA @System
inherits = fdm_filament_pla_silk
from = system
setting_id = OGFSL99_01
instantiation = true
filament_max_volumetric_speed = 7.5
filament_retraction_length = 0.5
compatible_printers =

[filament:Bambu PPA-CF @System]
inherits = Bambu PPA-CF @base
from = system
setting_id = OGFSN06_00
instantiation = true
compatible_printers =

[filament:Bambu PVA @System]
inherits = Bambu PVA @base
from = system
setting_id = OGFSS04_00
instantiation = true
nozzle_temperature = 240
nozzle_temperature_initial_layer = 240
compatible_printers =

[filament:FDplast SBS @System]
inherits = FDplast SBS @base
from = system
setting_id = SBS01_00
instantiation = true
compatible_printers =

[filament:Bambu TPU 95A @System]
inherits = Bambu TPU 95A @base
from = system
setting_id = OGFSU00
instantiation = true
filament_max_volumetric_speed = 3.6
compatible_printers =

[filament:Bambu TPU 95A HF @System]
inherits = Bambu TPU 95A HF @base
from = system
setting_id = OGFSU00_00
instantiation = true
compatible_printers =

[filament:COEX TPE 30D @System]
inherits = COEX TPE 30D @base
from = system
setting_id = C0X30D20
instantiation = true
filament_max_volumetric_speed = 3.5
compatible_printers =

[filament:COEX TPE 40D @System]
inherits = COEX TPE 40D @base
from = system
setting_id = C0X40D18
instantiation = true
filament_max_volumetric_speed = 5.5
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:COEX TPE 60D @System]
inherits = COEX TPE 60D @base
from = system
setting_id = C0X60D19
instantiation = true
filament_max_volumetric_speed = 6.5
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:COEX TPU 60A @System]
inherits = COEX TPU 60A @base
from = system
setting_id = C0X60A17
instantiation = true
filament_max_volumetric_speed = 1
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =

[filament:Elegoo TPU 95A @System]
inherits = Elegoo TPU 95A @base
from = system
setting_id = OGFSE07_00
instantiation = true
compatible_printers =

[filament:FDplast TPU @System]
inherits = FDplast TPU @base
from = system
setting_id = TPU01_00
instantiation = true
compatible_printers =

[filament:Overture TPU @System]
inherits = Overture TPU @base
from = system
setting_id = OGFOT008
instantiation = true
filament_flow_ratio = 0.95
filament_max_volumetric_speed = 8

[filament:AliZ PETG-CF @System]
inherits = AliZ PETG-CF @base
from = system
setting_id = AliZGFSG50
instantiation = true

[filament:AliZ PETG-Metal @System]
inherits = AliZ PETG-Metal @base
from = system
setting_id = AliZGFSG50
instantiation = true
compatible_printers =

[filament:COEX PLA+Silk @System]
inherits = COEX PLA+Silk @base
from = system
setting_id = C0XPLS03
instantiation = true
filament_max_volumetric_speed = 15
filament_long_retractions_when_cut = nil
filament_retraction_distances_when_cut = nil
compatible_printers =